You can run a chainsaw without a chain, but I wouldn’t recommend this for more than a few minutes. The engine will rev up higher, and these increases wear and tear. It can also run hot when the throttle is used. Ensure that you empty the bar oil tank, else oil can spray out of the chainsaw.
A question I sometimes get is if you can run a chainsaw without a chain. It is not recommended to run a chainsaw without a chain. You can run a chainsaw without a chain but try to do that just for a few minutes.
Since these guys bought 18 saws in one lick, probably at a discount,the kneejerk reaction was to bend over backwards, etc. Constantly started, revved at full speed for a few seconds, then turned off,hundreds of times a day, for a full month. They warrantied them anyway, giving them a bunch of new saws, and a bunch of new carbs, and with me being an e-bayer, I saw a huge pile of leftovers.
Running a saw without the bar and chain could possibley cause the clutch and drive sproket to go flying off. Safety wise a chainsaw without the chain is still VERY dangerous. Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction.
You’ll also learn the most common reason chainsaw bar oil stops flowing to the bar and chain. Chain teeth breaking off and flying from the saw chain as it wears is a real concern, especially when you run a saw without bar oil. Blocked saw oil port – remove the bar and chain, clean port and run saw to check feed.
can you run a chainsaw without the bar and chain Related Question:
Can you start a chainsaw without a clutch?
A clutch is an absolute necessity on a chainsaw. Without one, the chain sprocket would be connected directly to the motor, and the chain would turn even when the engine is idling.
What happens when a chainsaw bar is worn out?
As a chainsaw bar wears out, you lose cutting accuracy and cuts take longer. If the same type of cuts that your saw used to breeze through now take twice as long—even with a sharp chain—you might look at how worn your bar has become.
What happens if you don’t use bar and chain oil?
No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Why is it so hard to pull start my chainsaw?
If your chainsaw is hard to pull, here are some common causes: The pully system is snagged or stuck. The starter assembly is stuck or sticky. The housing may be damaged.
Why do chainsaws have clutches?
The clutch allows the engine to turn freely at low rpm [rpm=revolutions (turns) per minute] without moving the chain. They are separate. Unlike a four wheeler or truck, the chainsaw operator doesn’t have to engage the clutch or put the chainsaw in gear.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Why is my chainsaw bar smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Can you use wd40 on a chainsaw?
Step 5: Lubricate Your Chainsaw Before you put the chain back onto your chainsaw you will have to lubricate it to clean it, using WD-40® Multi-Use Product. Before refitting the chain into the chainsaw, wipe off all the excess residue and then reattach it to the guide bar.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
How long does it take to Unflood a chainsaw?
The first option is the easiest since it doesn’t require any effort on your part, it just takes time. Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Why does my chainsaw have too much compression?
Many problems with compression are related to fuel. Old or bad fuel can cause lots of headaches with yard equipment. Try draining any of the gasoline mixture left in the gas tank and add fresh fuel. If this does not solve the problem, it may be related to excessive fuel caused by problems in the gas lines and filters.
How do you rewind a chainsaw pull start?
Feed the cord through the holes in the housing and pulley, and tie a knot in the end. Keep tension on the cord with one hand while you release the pliers with the other. Let the pulley slowly rewind. It will wrap the cord around itself and stop when the handle contacts the housing.