The power behind a chainsaw provides almost everything you need to guide and control your cut, with very little effort on your part other than keeping it steady and providing enough pressure for the chain to its job. When you feel as if your cuts are taking much longer than they should, or you find yourself exerting much more force behind the chain than what you consider normal, you may want to look into why your chainsaw is not cutting in the manner it is designed to. If your chain is spinning, but not cutting, or the chainsaw is not cutting straight, then you need to address the chain itself- as I will explain in more detail below.
Take the guess work out of your repairs with our Fix app. Tap to download and it’s as easy as snapping a photo to find repair parts guaranteed to fit.
The common chainsaw includes a body, a 2-cycle engine, a gas tank, handles, a guide bar, a clutch and chain that fit around the bar. As the chainsaw is running the chain or teeth rotates around the guide bar at high speed, which permits the teeth to cut through wood. If the chain is too tight or loose, adjust it by loosening the nuts that hold the bar in place, then tighten or loosen the bar’s adjustment screw as necessary and then re-tighten the guide bar nuts.
Chain tension can definitely stall your chainsaw’s ability to cut correctly, even with a sharp chain. No matter how precise your chain tension is or how sharp the cutting teeth are, if your chainsaw’s chain isn’t mounted correctly, it isn’t going to cut anything. If there is no need to replace the bar on your chainsaw and you feel confident in your cutting teeth sharpening skills, chain placement, and chain tension, you need to keep reading!
chainsaw does not cut Related Question:
Why does my chainsaw not want to cut?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.
Why does my chainsaw smoke and not cut?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why is my chain saw not working?
A saw that won’t start or runs rough can cause you to think the carburetor is out of whack, but it may just be a neglected air filter. If the filter is clogged, the ratio of air to gasoline in the carburetor will be off. This can lead to a fouled spark plug and a clogged spark arrester screen inside the muffler.
Why is my chainsaw blade not spinning?
The chain tension may be too tight. Easy fix, just loosen the bar-retaining nuts and rotate the tensioning screw counterclockwise to the correct tension. Then tighten the nuts back up.
How long should a chainsaw blade last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Why is my chainsaw jamming?
Here are our explanations! Indeed, whether it is a chainsaw electric ou thermal, it is the teeth of its links that come into direct contact with the wood and the materials to be cut. As a result, dirt, wear on the guide or links and even the motor can be the cause of jamming.
How long do chainsaws stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
How many times can a chainsaw chain be sharpened?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
How often should I change my chainsaw chain?
The chain sprocket must be replaced if the depth of the wear marks reaches about 0.5mm, i.e. the wear limit. A seriously worn chain sprocket can cause the chainsaw chain and guide bar to wear at an increased rate, as well as reducing cutting performance too, so it’s important to keep an eye on.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why do loggers run upside down bars?
Every chainsaw bar has been designed to be mounted right-side up or upside down. The reason for this is that it allows the user to extend the life of his chainsaw bar by 50%. Flipping the bar will give the heavily-used areas some relief from wear and tear.
Why does my chainsaw cut curves?
Two main reasons will cause the chain to cut on a curve. The most common reason is from improper hand filing. If one side of the teeth is more heavily damaged, sharpening them down will make them smaller than the other side.