If a chainsaw cuts at an angle rather than cutting straight, then the problem most certainly lies in the guide bar and chain assembly. Adjust the chainsaw bar: If possible, adjust your chainsaw bar on a bench before continuing. Use a bar cleaner handle: A bar cleaner hook tool removes debris stuck in the bar’s rails.
Most of the time when a saw won’t cut straight, it’s caused by a problem with the saw chain. Most of the time, when a saw won’t cut straight, the chain is the culprit. Since a saw chain is a “Team” of cutter teeth, the cut will pull in the direction of the side whose cutter teeth take the biggest bites.
Your chain will have links on both sides of the chain. As I mentioned earlier, the chain is most likely the root cause of your problem, but if that’s not it, then it could also be your chainsaw bar. Use your gauge tool to clean the oil hole on both sides of the bar, to keep your chain running smoothly.
The most probable reason why a chainsaw pulls either to the right or left during a cut is because it was sharpened unevenly. Keep working the side which you feel lacks attention, and eventually the chainsaw should start going as straight as new. The teeth have to be equally sharp on each end to make the chainsaw work straight.
chainsaw does not cut straight Related Question:
Why is my chainsaw cutting at an angle?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
Why is my Stihl chainsaw not cutting straight?
In general, there are several reasons why a chainsaw is not cutting straight. The chain is not sharpened on both sides, the chain’s tension isn’t adequate. The chain’s thickness is less than the groove’s width. As a result, it doesn’t stay vertical in the groove and cuts at an angle.
Why does my saw not cut straight?
The primary reason why a miter saw might not cut straight is an inability to clamp the material down. The machine is designed to pull the material towards the blade during each cut, and if there’s a malfunction in this process, it might result in inaccurate cuts. Other reasons are: damaged blade.
How do I stop my chainsaw from cutting crooked?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
Why does my chainsaw smoke when cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does my chainsaw burn the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Can a bent chainsaw bar be straightened?
Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .
Why is my chainsaw chain not tightening?
If you’re having trouble tightening the chainsaw chain, it may be adjusted properly already. Check the tension on the chain by grasping it in the middle of the top of the guide bar and giving it a quick snap. The chain should quickly snap back into place with no sagging on the underside of the guide bar.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Why does my chainsaw chain dull so quickly?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
Is it OK to cut wet wood with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.