If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel. If you believe fuel has flooded the chainsaw engine, pull the starter cord several times while holding the throttle, dry and replace the spark plug, and then try starting the chainsaw again. Gasoline will start to deteriorate if left unused and sitting, so if the chainsaw hasn’t been started in a while, be sure to check that old fuel is not collecting inside the chainsaw.
Here, we look at the top 11 reasons why your chainsaw won’t start. Another common reason a chainsaw won’t start is that the sparkplug is old, dirty, damaged or not correctly attached. If the temperature is too low, it can make it hard to start a chainsaw.
A chainsaw can be a very useful tool for homeowners and professionals alike, until it stops working! When your chainsaw won’t start, it can cause a setback with your project and could even set you back financially for repairs. In this chainsaw starting guide you’ll learn the common problems that can arise with chainsaws as well as possible solutions. The recoil starter assembly consists of several elements that initiate the engine when starting the chainsaw such as the recoil starter pulley and rewind spring.
The question of why won’t my chainsaw start can be very hard to answer since the smallest thing can make a perfectly fine chainsaw go from working to being a large paperweight. If a chainsaw sits for a long time and wasn’t stored properly it can cause you all kinds of headaches and be a reason your chainsaw won’t start. The carburetor of a chainsaw is important and can be the reason that the chainsaw won’t start and the fix can either be simple or expensive.
chainsaw does not start Related Question:
What causes chain saw not to start?
The carburetor might be clogged and needs to be cleaned. A chainsaw’s carburetor mixes air and fuel to start the internal combustion engine. If fuel has been left in the engine for too long, it can become sticky and clog the carburetor, preventing it from starting. If the clog is minor, clean out the carburetor.
How do you make a chainsaw start easy?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
How long does a spark plug last in a chainsaw?
A poorly functioning engine in a Stihl chainsaw can mean more work for the operator and can even be dangerous. Consequently, Stihl recommends replacing the spark plug after every 100 service hours.
How long to wait if chainsaw is flooded?
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Do you start a chainsaw with the brake on or off?
Check the Chain Brake When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Can I use wd40 on my chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
Can you clean carburetor without removing?
Use carburetor cleaner to remove deposits, clogs & debris Deposits inside the carburetor can clog fuel and air passages and reduce performance or stop the engine altogether. Luckily, you can take care of many of these problems quickly and easily; often without even removing the carburetor from the engine.
Can you use wd40 to clean a carburetor?
WD-40 Specialist® Carb/Throttle Body & Parts Cleaner with attachable precision straw is the only all-in-one carburetor cleaner spray you will need to clean your carburetor, throttle body, and unpainted metal parts. What makes this cleaner unique is the dual-action cleaning system.
Will a flooded engine fix itself?
Will a flooded engine fix itself? No. You have to take appropriate measures to restore the fuel and air balance in your car’s engine.
Can you use starter fluid to start a chainsaw?
If you do not use it often, then you are okay to use starter fluid to start the chainsaw up.
Can you use starting fluid to start a chainsaw?
Removing the air filter, spraying starting fluid into the carburetor and pulling the starting rope is another quick way to clear out the engine. Starting fluid creates a leaner fuel mixture that ignites more easily, and the operation of the engine clears out the combustion chamber automatically.
How often should you tune up your chainsaw?
Obviously this depends to some degree on how often and how heavily you use your chainsaw but experts generally recommend you get a professional service or check-up from every few months for heavier use to at least once a year for light use.