If the operator has repeatedly been trying to start the chainsaw through the recoil starter system, they may have accidentally flooded the engine with fuel. If you believe fuel has flooded the chainsaw engine, pull the starter cord several times while holding the throttle, dry and replace the spark plug, and then try starting the chainsaw again. Gasoline will start to deteriorate if left unused and sitting, so if the chainsaw hasn’t been started in a while, be sure to check that old fuel is not collecting inside the chainsaw.
To clear excess fuel from the carburetor, place the choke lever in the Off position, hold the throttle trigger fully open and pull the starter rope 5 or 6 times. Try to start the chainsaw after priming the carburetor. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine.
Here, we look at the top 11 reasons why your chainsaw won’t start. Another common reason a chainsaw won’t start is that the sparkplug is old, dirty, damaged or not correctly attached. If the temperature is too low, it can make it hard to start a chainsaw.
It is another reason why chainsaws are so hard to start. So in cases where it’s become difficult to start a chainsaw, then you should consider the temperature as a factor. It is amongst the main reasons why are chainsaws so hard to start.
Many homeowners have had chainsaws that are hard to start when it’s cold. The main reasons why your chainsaw is often hard to start when cold are;. How to fix a chainsaw that won’t start when it’s cold outside.
chainsaw is hard to start Related Question:
How do I make my chainsaw easier to start?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
What makes a Stihl chainsaw hard to start?
Problems starting a Stihl chain saw can be related to gasoline storage, spark plugs, and incorrect starting procedures.
Why won’t my chainsaw start when it’s hot?
When your chainsaw quits after it gets hot, you either have a problem with gas flow being restricted into the engine or with the spark. This is a common occurrence on older-model chainsaws. By replacing your spark plugs and keeping your gas lines clear you can reduce the chances of this problem recurring.
Can you push start a chainsaw?
The biggest advantage of an electric chainsaw is that you don’t have to pull a cord and it needs minimum effort to get it started. You can start it by just pushing a couple of buttons and there is no throttle to open.
How long to wait if chainsaw is flooded?
Many people wonder if a flooded chainsaw will fix itself? The answer is yes, but not always. By letting the chainsaw sit for about 20 minutes it will allow some of the fuel inside the engine to evaporate.
Should I start chainsaw with brake on or off?
Check the Chain Brake When engaged, the chain brake stops the chain from rotating around the saw’s guide bar. When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Is my chainsaw flooded?
One tell-tale sign that a chainsaw has flooded is the smell of fresh petrol near the muffler. To ascertain whether this is indeed the problem, simply disassemble the part, pull the starter cord as if you were switching on the engine, then dry it, reassemble it and try switching it on again.
What causes a chainsaw to vapor lock?
Vapor lock occurs when the fuel (usually gasoline) within the fuel delivery system overheats and vaporizes too rapidly. The resulting excess gas bubbles accumulate to the point of actually blocking normal fuel delivery.
How does a choke work on a chainsaw?
The choke position increases the richness of the air and fuel mixture the carburetor sprays into the cylinder. With the master control lever in the choke position, the flow of fuel into the engine increases and the flow of air decreases.
Will a flooded engine fix itself?
Will a flooded engine fix itself? No. You have to take appropriate measures to restore the fuel and air balance in your car’s engine.
How long to wait if engine is flooded?
Perhaps the best remedy for a flooded engine is time. Simply open the hood of your car and let excessive fuel evaporate for as long as you can. After about 20 minutes try starting your car again without hitting the gas pedal.