Important distinction: bar and chain oil is not the same as the engine oil that is mixed in with chainsaw fuel. The oil outlet port is where the oil from your oil tank leaks out into the oil hole on your chainsaw bar. If you see no oil AND you know your oil tank is full AND you’ve already thoroughly cleaned the oiler, then you have a problem with your oil pump or oil line.
“My neighbor dropped a large black maple last week. I went over to give him a hand.”I have an old Craftman that an elderly gent gave me 20 years ago. Haven’t run it in years, but it started right up. I was thinking of putting some solvent in the oil tank, and let it drip down to the pores that feed the bar.
chainsaw is not oiling Related Question:
How do you clean a chainsaw oil pump?
Clear any sawdust, congealed lubricant and dirt out of the oil outlet hole on the guide bar. Keep the oil pump tank clean: even if it is equipped with a filter, wipe away all dirt around the cap before refuelling. Regularly check and clean the tank vent and the filter itself.
Do Electric chainsaws need bar oil?
Electric chain saws derive their power from an electric source, so they don’t need fuel to run. Most gas chain saws require a premixed gas-and-oil fuel to operate properly. Electric chain saws don’t require this added oil, but the bar and chain do need to be properly lubricated.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Does a chainsaw need engine oil?
To run properly, all chainsaws need two types of oil for different jobs. The first is engine oil. The chainsaw shown here has a two-stroke engine, so it needs two-stroke engine oil mixed with the fuel to help cool and lubricate the moving parts inside the motor.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use regular oil for chainsaw bar?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.
Can I use cooking oil for chainsaw?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
Can you clean a chainsaw fuel filter?
Brush the air filter gently with a soft brush or wash it in warm soapy water then dry it. Do not use compressed air to clean it – compressed air can blow holes in the filter, allowing dust and debris into your carburetor.
Where is the oil adjustment on Stihl chainsaw?
Insert a small flat-head screwdriver into the oil adjustment screw on the underside of the chainsaw. Turn the screw clockwise to increase oil flow or counterclockwise to decrease the oil flow, reveals Stihl USA.
Where is the oil relief valve on a Stihl chainsaw?
Re: stihl oil vent Facing the muffler look to the lower left corner. You should see it there. Sometimes compressed air is necessary to remove it. After you have removed the plastic plug replace it with a 6mm machine threaded screw.