Chain tension can definitely stall your chainsaw’s ability to cut correctly, even with a sharp chain. No matter how precise your chain tension is or how sharp the cutting teeth are, if your chainsaw’s chain isn’t mounted correctly, it isn’t going to cut anything. If there is no need to replace the bar on your chainsaw and you feel confident in your cutting teeth sharpening skills, chain placement, and chain tension, you need to keep reading!
The next mistake that may be preventing your chainsaw from cutting is the amount of tension on the chain. Keep a new chain handy to swap out if your old chain breaks, or if you have a job you want to complete hassle-free. The reason why your chain won’t cut even after sharpening is that you did not sharpen the chain properly, the chain hasn’t been tensioned properly, the rakers are higher than the teeth, or you need to replace the chain.
Yeah, the chain is getting oil, I just fired it up and did the newspaper test. I know how to sharpen one, but I think this one is done.
The power behind a chainsaw provides almost everything you need to guide and control your cut, with very little effort on your part other than keeping it steady and providing enough pressure for the chain to its job. When you feel as if your cuts are taking much longer than they should, or you find yourself exerting much more force behind the chain than what you consider normal, you may want to look into why your chainsaw is not cutting in the manner it is designed to. If your chain is spinning, but not cutting, or the chainsaw is not cutting straight, then you need to address the chain itself- as I will explain in more detail below.
Most of the time when a saw won’t cut straight, it’s caused by a problem with the saw chain. Most of the time, when a saw won’t cut straight, the chain is the culprit. Since a saw chain is a “Team” of cutter teeth, the cut will pull in the direction of the side whose cutter teeth take the biggest bites.
chainsaw is sharp but won’t cut Related Question:
Why does my chainsaw not want to cut?
The most common cause of a chainsaw that won’t cut properly is a dull cutting chain. Try sharpening or replacing the chain. The chain may not have the proper amount of tension. If the adjustment screw is too loose, the chain may not make good contact with the wood.
Why is my chainsaw smoking and not cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does my chainsaw stick?
Chain tension Indeed, if a chainsaw chain that slackens with wear no longer cuts, it damages the guide, tires the engine and can be the cause of a blockage when it is too tight. In addition, the more the chain saw heats up, the more the tension of the links decreases, until they become too relaxed.
How long do chainsaws stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Which way should chainsaw teeth face?
The direction of the chainsaw blade is always the same regardless of the type or model of chainsaw. So the sharp edges of the blade should always face the clockwise direction. If you check from the top, you will notice that the sharp edges are facing the direction opposite the chainsaw body or motor.
Why does my chainsaw blade get dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
Why does my chainsaw chain keep coming off?
Chainsaw chains come off the bar due to worn-out bars, worn-out sprockets, and wrongly set tension. You should also note that with continued use, chains lose their tension and hence are more likely to come off the bar when you least expect it.
Why does the chain slip on my chainsaw?
One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How many times can you sharpen a chainsaw?
Cutters can be sharpened up to 10 times or more before the chain needs replacing. If your cutters are worn unevenly after a few sharpenings, a professional can regrind them to uniform shape. If you use the same chain for a few years, then buy a new one, the new one won’t mesh smoothly with the sprocket and bar.
How do you start a stubborn chainsaw?
Try to start the chainsaw after priming the carburetor. 5. Activate the choke by moving the lever to the full choke position and pull the starter rope 3 or 4 times to start the engine. If that doesn’t work, move the choke lever to half choke and pull the starter rope, 6 times maximum, to start the engine.
Can I use wd40 on my chainsaw?
We recommend using WD-40® Specialist® Fast Acting Degreaser and soak it for 10 to 15 minutes. Next, use a wire brush to remove all the grime (repeat several times) and wipe with a paper towel to make sure all the dirt is gone.