If I turn it bar side up and give it gas, it runs great. Useless for most of my cutting… but runs great in that position. I’ve tried a number of things: putting Seafoam in the tank, adjusting high/low/idle screws, replacing fuel filter, replacing spark plug, removing the fuel line and checking it for cracks, and moving the fuel filter around in the tank to try to get it into a different position.
SOLVED: Saw stalls when turned sideways and facing down. Loading…. Oops :Please try again.
If you fill your fuel tank up to the bottom, maybe that will solve your problem. Then drain the fuel out of the container and it will be clean. Then you can pour the clean fuel into your chainsaw.
chainsaw quits when turned sideways Related Question:
Why does my chainsaw dies when I turn it sideways?
Because the fuel covers the jets. When the bar points down or the saw is held sideways the jets no longer have fuel to cover them, it is air. The saw then runs lean and dies.
Why does my chainsaw keeps cutting out?
The main culprit behind a chainsaw engine that keeps cutting out is usually a dirty or wrongly adjusted carburetor. A faulty carburetor fails to supply the correct air-fuel mixture, also called the “charge”, to the engine. Causing the engine to cut out or stall.
Can you cut sideways with a chainsaw?
While a properly working chain saw helps you cut hours off your work time when felling trees or cutting logs for firewood, it can also be a dangerous tool when things go wrong. When a chain saw cuts sideways, it’s a clear indication that things aren’t as they should be.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
How do I know if my chainsaw carburetor is bad?
To test the carburetor, remove the air filter, pour a teaspoon of fuel into it, and pull the starter rope. If the engine starts momentarily and then dies, the carburetor is likely why the chainsaw won’t start.
Why does my chainsaw keep running?
The most probable – and easiest to fix – cause of chain rotation while the chainsaw engine idles is a poorly adjusted idle setting on the carburetor. The result is that too much fuel is delivered to the combustion chamber when the throttle is released, and the engine doesn’t really slow. says Chainsawr.
How do most chainsaw accidents happen?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
What happens if chainsaw hits dirt?
Don’t Cut Into Dirt In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch.
What does a spark arrestor do on a chainsaw?
The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.
How do I get my chainsaw to idle?
1 – When the saw is warm and not running, turn the adjusting screw in (clockwise) a half turn, start the saw, repeat this process until the saw idles. 2 – The saw now idles, great! But it should idle without the chain moving.
Can a 2 stroke run upside down?
Most engines will run fine upside down. Just make sure the fuel tank height is correct with the carb. If the plane is designed to use a 2 stroke inverted, it should have a setup in the instructions for the correct heights.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
How do you clean a carburetor without removing it?
To clean a motorcycle carburetor without removing it, you’ll need to remove the bowls at the bottom of the carburetor. Once the bowls are removed, spray some carburetor cleaner up inside, wait a few minutes, then spray again to ensure coverage. Then replace the bowls and start the motorcycle to assess how it runs.
How do you clean a 2 stroke carburetor without removing it?
Vacuum away any loose dirt, dust, debris, grime, and great on the surface with a handheld and cordless vacuum. Lay out rags or cloths at the base of the carburetor to catch runoffs and protect the surfaces. Apply the carburetor and choke cleaner in thin, even coats. Then, wait for it to settle and work its magic.
How do I know if my chainsaw is running too lean?
If your chainsaw is running lean, it will take a long time to return to idle once you rev it up at a high rpm. Idle means the chain isn’t spinning even though the engine is on. Also, the saw will work at a higher rpm than recommended, but it will have less cutting power due to the lack of gas in the mixture.