Steps for changing a circular saw blade Unplug the saw’s power cord from the electrical outlet or extension cord. Use the blade wrench to tighten the arbor nut until it’s snug; be careful not to over-tighten the nut or it’ll be difficult to loosen it the next time you change the blade. If the saw has a diamond-shaped arbor, straddle the blade over two wood blocks and use a hammer or punch to tap out the diamond insert from the center of the saw blade.
circular saw blade exchange Related Question:
When should I change my circular saw blade?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
How do you put a blade on a circular saw?
Use the blade wrench to remove the arbor nut holding the blade in place. To loosen the nut, turn the wrench in the same direction as the blade cuts. Retract the saw’s upper blade guard and remove the old blade. Slip the new blade onto the saw’s arbor, making sure the saw teeth face in the direction of rotation.
How do I know what size blade my circular saw is?
Circular saws are generally 6.5 inches or 7.25 inches, while table and miter saws are 10 -12 inches. Select the saw blade the matches the size of your saw. 6.5in. blades go with 6.5 in.
Is it worth sharpening circular saw blades?
When your circular saw blade becomes dull, not only will it give you a rougher finish, but your saw’s motor will have to work harder and may burn out sooner. Sharpening your saw blades will save you money in the long run because you’ll get better cuts, and you’ll have to replace your saw and blades less often.
Which way do teeth go on circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
Which side should the blade be on a circular saw?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Why is my circular saw blade loose?
Bearings and washers are mainly responsible for holding a saw’s shaft in place. However, wobbles and misalignments may loosen the blade. This can cause problems while cutting. Moreover, the bolt of the circular saw may wear out after regular use.
How do I change the blade on a Ryobi circular saw?
How do I change the blade? Disconnect the power cord or remove the battery from the tool. Press the spindle lock button and use the blade wrench to remove the blade screw, outer washer and blade. Place new blade into the saw and attach the washers.
Can I use a 7 inch blade in a 7 & a quarter inch circular saw?
The only fine-tooth blade you have lying around is a 7 ¼ inch size. The short answer to the above questions is that you can generally use a smaller blade in a circular saw – within reason. Of course, there will be some drawbacks and changes in performance, especially when you size down by a significant margin.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
Can I use a bigger blade on my circular saw?
Can I use larger blades? Short answer: No. Long answer: You should only ever use larger circular saw blades, when the difference is fairly negligible (1 mm / 1/16″). The reason for that is that for safety reasons most saws are built to tight tolerances.
What can I do with an old circular saw blade?
The best thing to do would be to recycle them at a scrapyard near you. Donate them to a school that has wood shops, art departments, or theater programs. Make interesting pieces of jewelry such as earrings out of circular saw blades. You can use a jigsaw to cut and shape them the way you want.
Can Diablo blades be sharpened?
To ensure your Diablo cutting tool continues its high performance standards, please contact one of our approved “Authorized Sharpening Service Centers”.
Can carbide circular saw blades be sharpened?
A good quality carbide blade can be sharpened 3-4 times before some or all the teeth need to be replaced and sharpening is a fraction of the cost of purchasing a new blade. As long as your blade is not warped or severely damaged, the correct answer is yes, the blade should be sharpened.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
