Have installed my kitchen, and as all joiners/fitters are packed out i am going to attempt to do the worktops myself. The hob is going inbetween chimney breast so i’m a bit concerned that i’ll be hacking the worktop to bits. I have a “Drop in / standard” sink, which already has a seal inegrated in, i assume usually used on standard worktops wth clips.
In my experience, jigsaws work fairly well, but the blade inevitably flexes during a long cut and this results in a less-than-square angle as the cut progresses, so I’m considering using a circular saw. Compact laminates add additional layers to the manufacturing process until the desired thickness is achieved. Even a tracksaw with a diamond tipped cutter has to approached with caution.
Since Compact Laminates usually consist of melamine or phenolic resin impregnated papers or wood fibres, their machining is always associated with high tool wear. Especially for grooving and sizing with neutral cutting properties. AT A GLANCE.Alternating shear angle for neutral cutting behaviour during grooving and sizing.
circular saw blade for compact laminate Related Question:
Can you cut compact laminate with a circular saw?
Compact worktops can be easily cut using standard TCT blades. A circular saw should be used cut worktops to length where the cut edges are to be fitted against walls and remain unexposed.
Can I cut compact laminate jigsaw?
Compact Laminate is very very hard and as such simply eats any blades (other than diamond tipped)for breakfast. Buy loads and loads of metal cutting jigsaw blades and use them to cut within a few mm of your finish line on end cuts or cutouts.
What is a carbide blade?
With something like a carbide-tipped saw blade, the main body of the blade is made of steel. The small tips of carbide are brazed on to the body. A good carbide tip might hold an edge ten to twenty times longer than a tool steel tip. The carbide tip on a typical circular saw. Carbide tips do get dull eventually.
How do you cut solid grade laminate?
Cuts that will be hidden (i.e. a cut-out to accommodate an overmount sink) can be started with a drill-hole in each corner of the aperture, and the rest can be cut-out using a hand-held jigsaw, router cutter (12mm or 12.7mm cutter recommended) or a circular saw with a rail guide and TCT triple chip blade.
Is Compact laminate any good?
Compact Laminate worktops are a great choice for the budget conscious. they have the benefits of being readily available from most DIY stores and are available in a multitude of style options. Resistant to marks and stains.
What is compact laminate?
Compact laminate is made from layers of recycled paper fibres that have been dipped in resin and dried. These layers are stacked and sandwiched between laminate before being compressed under high pressure and heated to permanently meld together.
Can you drill compact laminate?
Compact laminate is extremely dense and brittle – it is too difficult for even a professional to drill into successfully. Can’t be unassembled. Silicon based glues can be replaced – you just need to cut the glue with a sharp blade.
What is a TCT blade?
A TCT (Tungsten Carbide Tipped) blade is a resharpened circular saw blade. TCT saw blades can be used for the following items: wood, some ferrous metals, non-ferrous metals and plastics. Typically, a saw blade is a toothed blade designed to cut metal.
How do you cut a zenith compact laminate floor?
How should you cut Zenith solid laminate worktops? Use a hand held circular saw with clean, sharp TCT triple chip blades, followed by a handheld router to achieve a high quality finish when cutting Zenith worktops for joint edges and finished ends.
How do you drill laminate without chipping?
Slow the speed of the drill down as you drill through the sub-material between the front and back Formica laminate surfaces. Keep the speed slow and apply less pressure as you drill through the back and complete the hole. Stop the drill once you have drilled through the back, and remove the bit carefully from the hole.
Can you drill holes in laminate countertops?
Things You’ll Need Make a hole in laminate countertop using an electric drill. Laminate countertops are typically constructed of a pressed-wood material and topped with plastic sheathing. You can use an electric drilled equipped with a common multipurpose bit to drill through laminate countertops.
Are carbide blades good?
Carbide-tipped blades are much harder and more heat and impact resistant, making them deal well with steel and lasting up to 200 times longer than the basic carbon steel blade.
What are tungsten carbide blades used for?
Tungsten carbide has been used in industrial cutting applications for nearly a century. In such a setting, where cuts are controllable and repeatable, its high durability and wear resistance allow it to outperform steel tools, cutting faster and leaving a better surface finish on machined parts.
What can carbide blades cut?
Carbide tipped saw blades cut almost everything from asbestos to Zirconium, including paper, plastics, rubber, steel, insulation, aluminum, and even food, as well as every kind of wood in the world and all the wood composites.
How strong is compact laminate?
It is extremely durable and will last for decades. You save hundreds or even a thousand pounds compared to solid surfaces, quartz, or natural stone worktops. It uses renewable materials making it an eco-friendly choice.
