“I need a 7¼” blade to cut 4×8′ sheets of plywood for cabinets. Handle the saw carefully because the telescoping blade guard will not extend through the zero-clearance base to cover the spinning blade. Then retract the saw blade above the base, and attach the zeroclearance plate using double-face tape.
In general, many woodworkers either use combination blades or rip blades when cutting plywood, and both types of blades are perfect for plywood cutting. Given the many types of brands and models of circular saw blades in the market today, choosing the best blades become doubly difficult. A circular saw is a versatile tool, and as long as you are using the right blade, you can quickly cut through plywood using a circular saw and end up with a refined finish.
Make circular saw cuts so clean that you don’t have to sand or touch up the plywood edges. Cutting speed depends on many factors, including the type and sharpness of the blade and the type of plywood you’re cutting. Spike Carlsen, an editor for The Family Handyman, will show you how to cut construction grade plywood and finish grade plywood with a circular saw in our video tutorial.
The thin kerf and wide set teeth enable a blade like this to cut to softwoods like pine and pressure treated beams a little more easily. The excessively high tooth count cut very slowly, which actually can cause the blade to become pinched between the pieces being cut and cause burning. Not related to the cut itself, but the blade doesn’t have any relief cuts or stabilizer vents.
circular saw blade for finished plywood Related Question:
What saw blade is best for plywood?
To get the best-quality cuts, invest in an 80-tooth blade designed for sheet goods. The small teeth take little bites to reduce chip-out and are steeply beveled at their edges to score the veneer face. You’ll have to slow your feed rate, but will get a much smoother edge.
How do you cut a plywood with a circular saw without splintering?
To do so, place the best side (meaning the side of the door that will be most visible once it’s hung) face down. Then score along the edge of the cut line with a sharp utility knife. Now when you make the cut, the wood fibers will break off cleanly at the scored line, leaving a smooth, splinter-free cut.
How many teeth should a circular saw plywood blade have?
Framing blades have 24 teeth and are effective for jobs such as rough carpentry, where speed is more important than getting a clean cut. Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering.
What circular saw blade is best for cutting plywood and why?
Best Circular Saw Blade: Ultra Fine Finish With 60 teeth and a . 059-inch kerf, the Freud D0760X Diablo Circular Saw Blade creates clean, smooth cuts on delicate material like veneer plywood and melamine. This thin kerf greatly reduces the chance of chipping and blowouts, and doesn’t waste any material.
How do you cut plywood cleanly?
The best thing you can do to get clean cuts in plywood is to use a zero-clearance insert. This closes the gap around the blade in the throat plate or shoe. On a table saw, you can buy an aftermarket insert blank, or you can easily make one yourself.
How do you cut a large plywood with a circular saw?
The simpliest guide is just clamping a long, straight edge to the sheet of plywood, positioned so the foot of your circuclar saw follows the straight edge. Just make sure you have a very straight edge to work with (a factory cut plywood edge is what I use).
What is a 24 tooth blade used for?
For most construction work, a 24-tooth general use blade is sufficient. That blade is very aggressive and will help you rip and cross-cut lumber and sheet goods quickly and with a high degree of accuracy. With a 24-tooth demo blade, you’re getting work done quickly, but you won’t get a near-finished edge.
What is a 60 tooth saw blade used for?
A crosscut blade, on the other hand, is designed to produce a smooth cut across the grain of the wood, without splintering or tearing. This type of blade will usually have 60 to 80 teeth, and the higher tooth count means that each tooth has to remove less material.
What is a 180 tooth saw blade used for?
Designed for cutting a variety of materials, including plywood, vinyl siding, and plastic, the CRAFTSMAN 10-in 180-tooth high-speed steel miter/table saw blade set is a must-have for your workshop.
Is more teeth on a saw blade better?
Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate.
How many teeth do you need for plywood?
Cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade.
How do you cut plywood without a blowout?
Install the proper blade on your circular saw for different kinds of plywood. For precision cuts on hardwood plywood such as in cabinetry, use a carbide-tipped blade with square-cut teeth. Known as a cross-cut blade, it cuts smooth and straight without chipping or splintering loose fibers.
Does Home Depot charge for cutting plywood?
Home Depot will cut plywood for free, provided you have purchased the material from the store. Employees will offer the first 10-15 cuts for free before charging a 50 cent fee per cut. Alternatively, you can purchase a circular saw or rent one for 4-hours, 1 day, 1 week, or 4 hours.
How do you cut plywood by hand?
Cutting Plywood With a Handsaw Always start with a sharp saw blade. A miter handsaw has a stiffer blade and will help if you’re making smaller cuts. For longer cuts that need to be straight, consider using a stiff board as a jig to guide your saw blade. Simply clamp the board along your cut line.
How do you make plywood straight edges?
Try attaching one of the crooked sheets of plywood to one with a straight edge with a hot glue gun. Run through the table saw, then detach, flip it over and run it again.
