“I need a 7¼” blade to cut 4×8′ sheets of plywood for cabinets. Handle the saw carefully because the telescoping blade guard will not extend through the zero-clearance base to cover the spinning blade. Then retract the saw blade above the base, and attach the zeroclearance plate using double-face tape.
In general, many woodworkers either use combination blades or rip blades when cutting plywood, and both types of blades are perfect for plywood cutting. Given the many types of brands and models of circular saw blades in the market today, choosing the best blades become doubly difficult. A circular saw is a versatile tool, and as long as you are using the right blade, you can quickly cut through plywood using a circular saw and end up with a refined finish.
Its extremely thick hardened plate is the reason why the model is considered the best 7 circular saw blade for plywood. In the second position, we have nominated a miter/table saw blade from a highly popular brand called DEWALT for the best circular saw blade for plywood. Take hold of the saw blade for plywood before activating it and don’t release the blade until it’s turned off.
The thin kerf and wide set teeth enable a blade like this to cut to softwoods like pine and pressure treated beams a little more easily. The excessively high tooth count cut very slowly, which actually can cause the blade to become pinched between the pieces being cut and cause burning. Not related to the cut itself, but the blade doesn’t have any relief cuts or stabilizer vents.
circular saw blade for hardwood plywood Related Question:
What blade is best for cutting plywood?
To get the best-quality cuts, invest in an 80-tooth blade designed for sheet goods. The small teeth take little bites to reduce chip-out and are steeply beveled at their edges to score the veneer face. You’ll have to slow your feed rate, but will get a much smoother edge.
What circular saw blade is best for cutting plywood and why?
Best Circular Saw Blade: Ultra Fine Finish With 60 teeth and a . 059-inch kerf, the Freud D0760X Diablo Circular Saw Blade creates clean, smooth cuts on delicate material like veneer plywood and melamine. This thin kerf greatly reduces the chance of chipping and blowouts, and doesn’t waste any material.
How many teeth should a circular saw plywood blade have?
Framing blades have 24 teeth and are effective for jobs such as rough carpentry, where speed is more important than getting a clean cut. Plywood blades have 100 or more fine teeth designed to create a finish with minimal splintering.
Can I use a circular saw on plywood?
Circular saws can be used to make square, miter, bevel and compound-angle cuts. When fitted with the appropriate blade, it can even cut metal and concrete. However, there’s one job for which the circular saw is particularly well-suited: cutting large sheets of plywood down to size.
What do you put under plywood when cutting?
The Secret is 2×2 Foam Board Here I have 8 laid out to support a full sheet of 3/4″ plywood. And unlike full insulation sheets, they are so easy to store. I just stack them up on a top shelf or under my bench.
Is more teeth on a saw blade better?
Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate.
What is a 140 tooth circular saw blade used for?
OVERVIEW. The CRAFTSMAN 7-1/4-in 140-tooth carbon circular saw blade is made for cutting plywood, OSB and plastic. With a fully hardened and fully flattened plate, along with 140 precision-ground teeth, this blade delivers precise cuts without chips or splinters in the wood or cracks in vinyl and plastic materials.
Is more teeth on a circular saw blade better?
A blade with a lower tooth count tends to cut faster than a blade with a higher tooth count, but the quality of the cut is rougher, which doesn’t matter if you’re a framer.
What is a 180 tooth saw blade used for?
Designed for cutting a variety of materials, including plywood, vinyl siding, and plastic, the CRAFTSMAN 10-in 180-tooth high-speed steel miter/table saw blade set is a must-have for your workshop.
What is the purpose of the gullet on a saw blade?
Gullet. The space between the teeth and the body of the saw. This space holds the sawdust while the teeth are in the cut. The gullet must be large enough to hold all the sawdust produced.
What is the TPI for plywood?
Instead, select a 10- to 12-tpi blade for larger, gradual curves, or a 20-tpi blade for tight curves (1″ radius or less) in solid wood and all cuts in plywood or melamine-coated particleboard.
How do you cut plywood without a blowout?
Install the proper blade on your circular saw for different kinds of plywood. For precision cuts on hardwood plywood such as in cabinetry, use a carbide-tipped blade with square-cut teeth. Known as a cross-cut blade, it cuts smooth and straight without chipping or splintering loose fibers.
When cutting plywood with a circular saw which side is up?
Also note that a circular saw cuts on the upstroke, which often splinters the top edge (veneer) slightly. The bottom edge usually remains splinter-free. So always cut plywood with the good side down.
How do you cut a large plywood with a circular saw?
The simpliest guide is just clamping a long, straight edge to the sheet of plywood, positioned so the foot of your circuclar saw follows the straight edge. Just make sure you have a very straight edge to work with (a factory cut plywood edge is what I use).
How do you cut plywood cleanly?
The best thing you can do to get clean cuts in plywood is to use a zero-clearance insert. This closes the gap around the blade in the throat plate or shoe. On a table saw, you can buy an aftermarket insert blank, or you can easily make one yourself.
