Hi,. I need to cut down a new piece of laminate worktop, I have a circular saw but it still has the original blade so won’t be that sharp. I want to get a new blade but probably won’t use the saw again for years and not for anything I need a fine cut on, so I don’t want to spend a lot on a blade as it won’t be worth it.
I need to make a few straight edge cuts in my Axiom laminate worktop and was planning on using my Circular saw. The blade hasnt been used too much, but has been in the shed for ages and could do with replacing. On the side of the circular saw it says the blade used is 185mm x 16mm bore.
Cut the sink hole with the jigsaw – it will wander a bit but that doesn’t matter and don’t forget to seal the cut edge – I use silicon. For the worktop ends, as others have said, it helps to cut the bulk off first with a hand saw or even the jig saw, and then finish off taking a few mm with the router against a straight edge – makes the routing far easier and saves the cutter. Always cut into the laminate front edge so you don’t get breakaway.
circular saw blade for laminate worktop screwfix Related Question:
What circular saw blade is best for laminate worktops?
What blade should I use to cut laminate countertop? If you use a circular saw, it’s best to use a fine-toothed narrow blade with at least 40 teeth. When it comes to cutting laminate countertop, blades with carbide tips usually last longer than regular steel.
Can you cut a laminate countertop with a circular saw?
A good quality circular saw will most likely do the trick, although it is not just as simple as picking the right saw. Besides knowing how to cut laminate countertop, you will also need the proper tools for the job at hand.
Which saw blade for laminate?
To get a clean cut without replacing the blade repeatedly, it’s important to find a product with a thin blade width, or kerf. The best saw blade for cutting laminate flooring also should have a carbide, titanium, or diamond tip to help the blade move through the rough material.
How do you cut a laminate worktop with a circular saw?
If using a circular saw, set the blade depth to 0, position against your straight edge guide and move the saw in a clean motion from front to back. Repeat this, cutting deeper each time until you saw fully through the worktop. If you are making more precise cuts using a router, many of the same principles apply.
How can I cut my countertop without chipping?
Outfit the jigsaw with a blade designed for use with laminate or particle board. Then, use a drill with a spade or paddle bit to drill a starting hole for your countertop cutting jig. Cut around the outline, and then remove the remaining tape to reveal the clean edge.
How can I cut laminate without chipping?
You can minimize the potential for chipping if you use a finish blade with lots of teeth, making sure the sharp is keen. What is this? You can further reduce the chance of chipping by using masking tape along the cut line and cutting through the tape.
Is it easy to cut laminate countertop?
Cutting laminate countertop is a pretty straightforward process. Laminate countertop comes in standard sizes that you will just need to cut to length to fit your counter space.
How do you cut a laminate countertop by hand?
Measure at the top, bottom and middle of the edge along the countertop and place a pencil mark in each location. Draw the marks on top of the painter’s tape. Connect the marks using a straightedge so that the cut line is straight and square. Saw the counter along the cut line with the handsaw.
Is more teeth on a saw blade better?
Blades with more teeth yield a smoother cut. Blades with fewer teeth remove material faster, but tend to produce a rougher cut with more “tearout”. More teeth means you will need to use a slower feed rate.
Are miter saw blades universal?
As there are lots of circular blades available, know that they feature differing characteristics for differing uses. So, in response to the query are miter saw blades universal, the answer is no because they come in varying sizes for a variety of individual tasks meaning they are not universal nor interchangeable.
What is the best saw for cutting kitchen worktops?
Circular Saws A circular saw is the most efficient tool for cutting a worktop down to size.
Can you cut laminate worktop with a jigsaw?
The Bosch T101BR jigsaw blade is an ideal choice for cutting laminate materials. The blade cuts on the down stroke, not on the upstroke, the “R” in the product code referring to its “reversed” teeth. This is a popular blade often referred to as a worktop blade.
Do you cut worktops upside down?
You don’t need to turn the worktop upside down before cutting it. If the worktops are a dark color although sometimes I will do this anyway, place a strip of masking tape on the worktop where you need to mark it. This will make the pencil lines much more visible.
