I am using the circular saw seen below, and I would like to make a plunge cut, and I can’t figure out how to do it. The bladeguard is in the way, and although I can pull it back manually with the black lever seen at left under the XR logo, that requires one of my hands to remain occupied holding it back, which is not desirable- I need both hands to guide the saw, personally.
After cutting a few pieces, you should gain familiarity with the saw and how it feels. If you are cutting thin small bits of wood, you may have to flip the guard up with a finger or thumb as the waste material sometimes cut caught in the guard. “I’ve been using a 6.5” worm drive Skill saw for 30 years, never had a issue.
Do not place hand under the shoe or guard of the saw. Do not twist the saw to change, cut or check alignment. Refer to Powered Hand Tools – Basic Safety for Electric Tools for general safety tips.
Replacing the guard on your Porter Cable circular saw is an easy, short repair that you can easily do at home. Conclusion Replacing your Porter Cable circular saw guard is about as easy as a repair gets. The repair will help keep your saw blade properly covered when it’s not actually cutting, which means your saw will be safer than if you used it without the guard.
circular saw blade guard Related Question:
What is a power saw safety guard?
Portable circular saws. The lower guard shall cover the saw to the depth of the teeth, except for the minimum arc required to allow proper retraction and contact with the work. When the tool is withdrawn from the work, the lower guard shall automatically and instantly return to covering position.
Should a circular saw blade touch the guard?
Before each use, make sure the lower guard moves properly. The guard is the last line of defense between the operator and the saw. To test, raise the lower guard. Be sure the guard doesn’t touch the blade or any other part of the saw.
Why is the lower blade guard so important on a circular saw?
The blade guard is the most important safety feature of the tool because a circular saw takes time for the blade to come to a complete stop after a cut has been made.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
How do you keep a circular saw guard up?
This can be accomplished by rotating the guard into the saw, and holding onto the black handle with the thumb of the right hand (the trigger hand is the left). Pull the guard back before pulling the trigger.
What PPE should be worn when using a circular saw?
What should you do before start cutting with a circular saw? Wear safety glasses or goggles, or a face shield (with safety glasses or goggles). Wear an approved respirator or dust mask when exposed to harmful or nuisance dusts. Use appropriate hearing protection equipment in noisy areas.
What should you avoid when cutting with a circular saw?
Check for obstructions in stock Before cutting any material, especially wood, make sure there are not obstructions such as nails and screws embedded in the wood. Cutting a nail or screw embedded wood can cause damage to your circular saw, and worse still, might result cause injury to you.
Should you wear gloves using a saw?
Gloves won’t protect you from a saw blade. They may make an accident worse.
Why does my circular saw jam?
Most of the time, a circular saw keeps stopping because the blade gets stuck in the wood or material. This is due to the blade not being powerful enough to get through the material. It could also be because the blade is damaged or the motor is malfunctioning.
Do I need to lubricate circular saw?
The blade doesn’t need to be oiled very often; you can coincide the oiling with blade replacement, but a spot of oil on the inner washers will keep the saw running better and more safely.
Are Anti kickback pawls necessary?
The farther back from the rear of the blade, the less effective it is. Anti-kickback pawls should be the backup to the preceding two options – if you can’t, or don’t (despite your best efforts) prevent the kickback, the pawls will at least retard the return of the stock in your direction.
What is the space between two protruding teeth on a saw blade called?
Gullet (handsaw) The space between a saw’s teeth, where the saw dust is carried out. It is an equilateral triangle, just like the file that shapes the teeth.
How deep should a circular saw cut?
Don’t clamp both sides of a cut. For efficiency and safety, set the blade depth no more than 1/4-inch below the thickness of the board.
Why is a hacksaw blade harder than a wood saw blade?
Due to the different materials that these handheld saws are designed to cut, their blades also differ in thickness. The blade utilized by a hacksaw to cut metal materials and plastic is the thinner blade. The blade used to cut wood on a handsaw is thicker than the blades used on a hacksaw.
How must the saw blade be held after the cut is finished and before the blade stops rotating?
Hold the saw firmly and lower the blade slowly into the material being cut. After the cut is completed continue to hold the blade in the down position, release the off/on switch, wait till the blade stops rotating and the raise the blade to the up position.
