05-04-2015, 2:12 PM #1 Hello,I have an old, not used much, Craftsman circular saw. Recently the blade guard has stopped lifting up as i push into the cut. Its not really safe to use right now since I have to lift the guard to expose the blade into the cut.
A good cleaning cures a lot of problems 🙂 However, I always lift the guard before starting a cut anyway sometimes that stupid thing will catch or bind when starting and ruin the cut. Have your say… Forum Topics Woodworking Skill ShareYour woodworking skills are displayed for several lifetimes in each project. Show us your jigs, share your tips, strategies and, of c… 1917 Wood & LumberDifferent wood requires different woodworking strategies – from cutting to finishing.
circular saw blade guard stuck Related Question:
How do you remove a stuck circular saw blade?
Place the wrench on the arbor nut in the nine-o’clock position, or as near to that as possible. Hold the saw in one hand. With the other, bring the hammer down with a sharp striking blow on the end of the wrench. If the wrench falls off and the nut does not loosen, put the wrench back on and hit it again.
How do you remove a stuck Arbor nut?
Be sure to clean the threads off with a steel brush before you put on the new nut. Applying AeroKroil penetrating lubricant will generally allow easy removal of rusted and stuck nuts and bolts using only a wrench.
Why does my circular saw get stuck?
Most of the time, a circular saw keeps stopping because the blade gets stuck in the wood or material. This is due to the blade not being powerful enough to get through the material. It could also be because the blade is damaged or the motor is malfunctioning.
Where is the arbor lock on a circular saw?
Place the saw on a wooden surface and pull back the blade guard. If the saw has an arbor lock button on the top of the housing, press it in. The arbor is the shaft the blade installs on. If there’s no lock button, press the blade into the wooden surface.
How do you remove a Craftsman circular saw blade?
Usually, on a corded right-hand circular saw, the bolt will loosen counterclockwise. A left-hand saw will loosen clockwise. You can also look for the arrow on the upper or lower blade guard for the blade rotation. Loosen the bolt in the same direction as the arrow.
Why does my circular saw blade stop spinning?
The most common reason your circular saw blade stops spinning is because your workpiece is pinching the blade. This can also cause the blade to kickback. To prevent this from happening you need to support your workpiece properly to allow it to set securely through the entire cut.
Which direction do you turn the table saw arbor nut to loosen it?
If the arbor enters the blade from the left side of the saw (as most do), you need to rotate the top of the nut toward you to loosen it, away from you to tighten it. Note that this way, forces on the blade tend to keep the nut tight rather than encouraging it to work free.
What is an arbor nut?
Description: This item has been sourced from the original manufacturer and is intended to be used with table saws from Ridgid. The metal arbor nut fits over the outer blade washer and is used to secure the saw’s blade to the arbor shaft. A hex socket wrench is needed to install this item.
What is an arbor wrench?
This arbor wrench allows you to secure or remove saw blades. An angular profile of this item makes tightening and loosening the blade bolt extremely easy. This wrench is made out of metal and it is sold individually.
Why does my circular saw stop in the middle of a cut?
Too much blade will become exposed to wood, and the blade can get stuck. Proper use can also be a culprit causing your circular saw to stop mid-cut. Make sure you are moving the saw in a straight line or using a jig to keep the cut straight.
What is the space between two protruding teeth on a saw blade called?
Gullet (handsaw) The space between a saw’s teeth, where the saw dust is carried out. It is an equilateral triangle, just like the file that shapes the teeth.
What is the lower blade guard on a radial arm saw?
acceptable means of guarding the lower exposed portion of a radial arm saw blade. The purpose of the lower guard is to protect the operator from inadvertent contact with the saw blade teeth from the side. Accidental contact with the front or rear of the saw blade is not always preventable by the lower saw guard.
What does a brake do on a circular saw?
Electric Brakes – An electric brake stops the motor in about two seconds after releasing the trigger, while a saw without an electric brake will take about 10 to 15 seconds to stop. The electric brake works by reversing the flow of electricity to the saw motor.
Which way do the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How do you loosen a nut on a circular saw?
Press down on the saw’s arbor-lock button and rotate the blade until the locking mechanism engages. Use the blade wrench to remove the arbor nut holding the blade in place. To loosen the nut, turn the wrench in the same direction as the blade cuts.
