Something I didn’t like about it from the beginning is the guard is sloppy, which causes kickback when starting a cut. Idk if this is normal to other ircular saw brands, but I checked and this model is made like that from the factory so to prevent the kickback I had to pin the guard with a pencil as done by other people for other purposes. I’m not sure if it’s caused by the pinning or by the sloppiness of the guard.
A Snap Ring retains the Guard which pivots around the Shaft bearing on most circular saws. Definitely look at the diagram to see if yours is that easy of a fix!
Below, you can find the top three most common and most startling circular saw mistakes. Read on to learn how to fix these three shocking circular saw slip-ups. Storing your circular saw the right way reduces damage to the saw and blades.
The blade is now rubbing against the return blade guard once I have applied tension to it. Iturra sells a machined hinge for the top wheel that you can shim with included washers to move the top wheel axle left or right thus moving the top wheel left or right. The washer registers either side of the raised registrations on the blade guard, centering the blade guard.
After cutting a few pieces, you should gain familiarity with the saw and how it feels. If you are cutting thin small bits of wood, you may have to flip the guard up with a finger or thumb as the waste material sometimes cut caught in the guard. “I’ve been using a 6.5” worm drive Skill saw for 30 years, never had a issue.
circular saw blade rubbing guard Related Question:
Should a circular saw blade touch the guard?
Before each use, make sure the lower guard moves properly. The guard is the last line of defense between the operator and the saw. To test, raise the lower guard. Be sure the guard doesn’t touch the blade or any other part of the saw.
What is the guard for on a circular saw?
Blade guard: A retractable guard covers the circular saw blade when it isn’t operating. When the saw is lined up and ready to cut, the guard is lifted using a tab on its side. Shoe: Sometimes called the base of the saw, this is the metal rectangle that rests on top of the material being cut.
Why is the lower blade guard so important on a circular saw?
The blade guard is the most important safety feature of the tool because a circular saw takes time for the blade to come to a complete stop after a cut has been made.
Why does my circular saw get stuck?
Most of the time, a circular saw keeps stopping because the blade gets stuck in the wood or material. This is due to the blade not being powerful enough to get through the material. It could also be because the blade is damaged or the motor is malfunctioning.
Why do circular saws cut upwards?
The saw’s motor runs the blade rotation in a way that the circular saw teeth direction points up as it enters the wood you’re cutting. It’s intentional to create the most stable, accurate, and safe cutting. As the blade teeth hit the material, they rip from the bottom through the top.
How do you keep a circular saw guard up?
This can be accomplished by rotating the guard into the saw, and holding onto the black handle with the thumb of the right hand (the trigger hand is the left). Pull the guard back before pulling the trigger.
Are Anti kickback pawls necessary?
The farther back from the rear of the blade, the less effective it is. Anti-kickback pawls should be the backup to the preceding two options – if you can’t, or don’t (despite your best efforts) prevent the kickback, the pawls will at least retard the return of the stock in your direction.
What is the space between two protruding teeth on a saw blade called?
Gullet (handsaw) The space between a saw’s teeth, where the saw dust is carried out. It is an equilateral triangle, just like the file that shapes the teeth.
What should you do first before start cutting with a circular saw?
4. Use a safe depth of cut settings. Before cutting with a circular saw, you have to set the depth of cut to match the thickness of the board you’re trying to cut. When you set depth of cut, you need to make sure that too much blade is not exposed beneath the material you’re cutting.
Why do circular saws struggle to cut?
Here are some reasons your circular saw keeps stopping: Make sure your work piece is properly supported so it doesn’t pinch the blade which could also cause kickback in addition to stopping. Damaged, warped, loose or dull blade. Motor malfunctioning or overheating. Cable problems like frayed cord or weak connection.
Why does my circular saw blade stop spinning?
Blades may stop due to loose clutch (an odd looking washer where the bolt holds the blades into the saw arbor). So, if your motor is going properly and blades keep stopping then you need to replace the clutch or tighten it up.
How do I know if my circular saw blade is dull?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
What happens if you put a circular saw blade on backwards?
You can run a saw blade backwards and it cuts pretty well. However it is not at all a good idea. The two big reasons not to do this is that saw tips are much more likely to come off if the saw blade is run backwards and that the whole saw blade is much more likely to come apart if it is run backwards.
How do you hammer a circular saw blade?
Place the blade on the anvil. Hammer down all ridges or lumps while using as few blows as possible to avoid expanding the metal too severely. If there’s a loose area, mark it and hammer between the mark and the blade’s rim to stretch out unnecessary tension.
Which way should a saw blade rotate?
Like miter saws, table saw blades rotate clockwise, meaning the teeth should be pointing down.
