While the saw is ideal for those purposes, you can also use it to make furniture-grade cuts in wood, cut steel or aluminum, reduce unwieldly sheets of plywood to more manageable sizes, and do heavy demolition cuts through lumber that has nails in it. These blades are rated for steel plate, pipe and conduit, and shapes such as L, U, and squares; some blades are also designed for cutting the same shapes in aluminum, and a few blades are even rated for making the cut in stainless steel, a notoriously difficult material to cut. Not all metal-cutting circular saw blades will cut thin sheet materials such a roofing and metal trim.
Blade Types:Generally speaking there are four major categories of circular saw blades. Combination saw blades are designed to cut both rips and crosscuts and are the most common type of circular saw blades. Unless you have two circular saw blades available at all times, it would be more than a nuisance to switch from a rip to a crosscut blade every time you change the cutting direction.
circular saw blades in Related Question:
Which way does a circular saw blade go?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out. It’s not a hard, fast rule, though. You should always double-check.
What happens if you put a circular saw blade on backwards?
You can run a saw blade backwards and it cuts pretty well. However it is not at all a good idea. The two big reasons not to do this is that saw tips are much more likely to come off if the saw blade is run backwards and that the whole saw blade is much more likely to come apart if it is run backwards.
What are the different types of circular saw blades?
Blade Types: Generally speaking there are four major categories of circular saw blades. They are: Rip Blades, Crosscut, Combination and Specialty blades. Ripping saw blades are designed primarily to achieve a smooth, clean and safe cut when ripping wood or cutting in the same direction as the wood grain.
Which way should teeth face on circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
Do all circular saws rotate the same direction?
Circular Saws This means that the circular saw cuts wood on the upstroke. For a right handed circular saw (most common), this means that the blade rotates counterclockwise, which is similar to the table saw. For a left handed circular saw, the blade rotates clockwise.
Will a wood blade cut metal?
While a metal-cutting saw has a collection bin to prevent metal chips from getting into the machine, a woodcutting saw isn’t designed this way. If you do decide to use a wood saw on metal, only use a 7 1/4-inch blade and preferably a worm drive blade, which provides extra torque.
Can you reverse a skill saw blade?
Yes – a circular saw blade can be accidentally mounted on the saw backwards – but it is a mistake you will only make one time because you will find out the instant you try to cut a piece of wood. It will not cut and you will be embarrassed at your mistake.
When should I replace my circular saw blade?
Look for worn-down, chipped, broken and missing teeth or chipped carbide tips that indicate it’s time to replace a circular saw blade. Check the wear line of carbide edges using a bright light and magnifying glass to determine if it’s beginning to dull.
Why does my circular saw blade stop spinning?
The most common reason your circular saw blade stops spinning is because your workpiece is pinching the blade. This can also cause the blade to kickback. To prevent this from happening you need to support your workpiece properly to allow it to set securely through the entire cut.
How tight should a circular saw blade be?
In general, the blades on right-handed circular saws turn counterclockwise, so you’d tighten the bolt clockwise; the blades on left-handed circular saws turn clockwise, so you’d tighten the bolt counterclockwise.
What type of blade is best for circular saw?
Mostly, a 24-tooth circular saw blade is preferred by many people, especially if you have to cross-cut lumber and sheet materials. The 24-tooth blade is good enough for you if the diameter is 7¼”. However, as the diameter increases, you should also consider looking for circular saw blades with more teeth.
Are Diablo blades worth it?
Diablo blades are available in a wide selection of sizes and styles and are easy to find online and locally at Home Depot. The consensus is that Diablo saw blades balance great quality with excellent value, and are a good choice when replacing or upgrading the OEM blades that are often bundled with new saws.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
What is the space between two protruding teeth on a saw blade called?
Gullet (handsaw) The space between a saw’s teeth, where the saw dust is carried out. It is an equilateral triangle, just like the file that shapes the teeth.
