A circular saw is often used for most cuts, making it the best saw for deck building. Get one that cuts reliably, and equip it with a sharp carbide-tipped blade.
If you’re considering a DIY deck project, you’re probably wondering what tools you’ll need. The good news is, if you’re a handy guy or gal, chances are you already own many of the tools needed for deck construction. Deck tools can be divided into five categories: tools for lay out and measuring; for general carpentry and digging; for cutting; for fastening; and for smoothing and shaping.
This corded circular saw is great for any decking job. I purchased this replace a basic level Ryobi circular saw that I had for about 2 years and now had a warped base plate. The Ryobi turned on which such force that the saw would immediately shift a bit, but this starts up smoothly and has just as much power.
If you don’t know where to start, we’ve made a list of seven tools you need handy before you start to build a deck. Screwing down your decking boards, instead of nailing, will make for a stronger and safer deck down the road.The Right Hardware. When you gather all of your tools ahead of time, it makes the process of building your deck that much more enjoyable.
Circular saws are mainly used for cutting wood, but they can cut different materials with specialized blades. For all cuts, start the saw off the cut and push the blade into the board with a steady forward motion. Bevel Cutting: Bevel cuts will make the saw work harder, so clamp the board firmly to a work surface using a guide set so the blade will cut along the waste side of the line.
circular saw for cutting decking Related Question:
How thick of a board can a circular saw cut?
Circular Saw Features The larger the blade, the deeper the cut. The most common blade diameter is 7-1/4 inches. Most saws with blade capacities of 6 inches or more can cut through 2-inch dimensional lumber at a 45-degree angle in a single pass.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
What saw to use to cut deck boards?
A circular saw is often used for most cuts, making it the best saw for deck building. Get one that cuts reliably, and equip it with a sharp carbide-tipped blade.
Can I put a metal cutting blade on my circular saw?
Only blades and discs specified for cutting metal should be used. These professional circular saw blades are perfect for cutting through aluminium, copper, lead and other non-ferrous metals; while these diamond cutting discs will make light work of cutting through stainless steel.
How deep can a 5.5 circular saw cut?
It turns out that it’s a simple question but very essential when you are going to do a project using this kind of saw. To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements.
How shallow can a circular saw cut?
Circular saws turn corners about as well as a freight train, and standard models will cut only about 2 1/2 inches deep. There are ways around the shallow cut—for example, you can flip over a 4×4 and cut from two sides—but the curve limitation has no work-arounds.
Can you use a miter saw to cut deck boards?
Cutting The Deck You can either use a miter saw or a circular saw since composite cuts similarly to wood. Mark the board using a quick square while holding the square against the board’s face.
What can I use as a spacer for decking?
Sixteen-penny nails work great as spacers when you’re installing deck boards, but they often fall through the cracks. Keep the nails in place by pounding them through plastic jar covers. They’re easier to move and will stay up on the deck instead of falling on the ground.
What is the difference between a circular saw and a table saw?
Circular saws are lightweight, hand-held, and can be moved from jobsite-to-jobsite with ease. A table saw is heavier and more complex in its set up. Because of its weight and footprint, this tool is more difficult to move these saws around as easily as you are able to do with a circular saw.
What saw blade for composite decking?
What is the Best Saw Blade for Cutting Composite Decking? The EnviroBuild installation guide advises the use of a circular saw using a 40 tooth alternate top bevel finish blade to cut your composite decking boards.
What blade is best for cutting composite decking?
Diablo’s TrexBlade is the only recommended composite decking by Trex Company when cutting composite decking materials. These new blades deliver maximum performance and highest quality of finish; making it a ‘must-have’ tool for both professionals and DIYers planning composite decking projects.
What is a deck saw?
Saw Blades For Cutting Metal Deck A cut-off saw is a high speed machine designed to handle the heat created by cutting steel.
How do you cut angled deck boards?
Choose two straight boards and cut one end of each at a 45-degree angle. A 10-inch power miter saw will not cut all the way across the board. Complete the cut with a handsaw. If you are experienced using a power miter saw, lift up on the forward edge of the board to finish the cut.
Can I just replace deck boards?
If your existing deck is old, shabby and a maintenance nightmare, you don’t have to tear it all down and start over. Chances are that the structural parts are still in good shape. If so, you can simply remodel it with new decking, rails and stairs, and save tons of money over the cost of a complete rebuild.
What is the easiest way to remove deck boards?
Using Crowbars – The easiest way to remove decking boards is by using a crowbar and hammers. To make it easier, you can use two crowbars. First, gently pry the end of the decking board with one crowbar. Leave the first crowbar in place weighted down, then use the second crowbar to pry along the length.
