The saw guide definitely allowed me to cut down 11- 4 x 8 sheets much more quickly and easier than would have been the case if I had used my table saw. The cheap plastic construction means the guide won’t last very long and the short length of the guide required that I cut away the width that I don’t want for cuts greater than 24″ in width instead of cutting the width I do want, but having to take into consideration the width of the blade. As is, most of the plastic section that rides along the piece being cut reaches the end of the wood being cut before the circular saw blade has completed its cut.
“The Rip-Cut easily makes straight, accurate, repeatable cuts without measuring, marking, or having to keep the saw on the cut line. The Rip-Cut does this with a long edge guide that follows the straight edge of the sheet you are cutting. So, all you have to do is lock the saw in at the measurement you want – up to 24” – using the built-in measuring scale, and then make your cut. Just lock the saw sled at your desired cut width, and you’re all set, whether you need to cut one piece or make multiple pieces of the exact same size. Plus, the Rip-Cut makes it easier to cut down large sheets by yourself.
circular saw guide attachment Related Question:
Can you use a guide rail with a circular saw?
A Guide Rail is designed to be used with a Circular Saw for creating precise and straight cuts every time.
Is there a guide for a circular saw?
A circular saw guide rail is a critical tool for making straight cuts on large boards, but choosing the best one for your workshop is not easy because there are many brands available, and a lot of newer woodworkers aren’t sure how to tell the difference from one brand to the next.
Are guide rails universal?
The YouTool Guide Rail is universally suitable for almost all brands of saw, and is available up to 5 meters long.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
Does Kreg rip cut work with any circular saw?
A: Yes, the Rip-Cut will fit that saw fine. Helpful? A: The Kreg Rip-Cut is designed to work with a full size 7 1/4″ corded circular saw.
How do you use saw guides?
Figure A: Straightedge Guide Glue the fence to the base, then run the saw against the fence to cut the guide. The factory edge is used for the fence. To use the guide, simply clamp it to the piece you’re cutting, aligning the base with the cut line.
Are circular saw Rip Fences universal?
No, fences are not interchangeable on any circular saw. There are different widths. You can get a universal replacement set that would most likely fit.
How much does a miter saw cost?
A basic compound miter saw starts at $100, while miter saws with sliding blades start at $125. Dual-bevel miter saws start at $200, and professional-level miter saws with special features can cost as much as $800.
What does a rip fence do?
A rip fence provides a cutting guide that runs from the front of the table to the back. This is parallel to the cutting plane of the blade. A Miter gauge holds and guides material at a specific angle to make a precise cut. The locking mechanism pivots from 45 to -45 degrees and slides into a slot (miter slot).
Are track saws worth it?
Conclusion. A track saw is unbeatable when it comes to making long, accurate cuts. It can do most things a table and circular saw can, while being more portable than a table saw and more accurate than a circular saw. It’s also better than a table saw at breaking down large sheets of plywood.
Is it a guardrail or guide rail?
According to the US Federal Highway Administration, “The terms guardrail and guiderail are synonymous, and are used in different regions around the country.” Guide rail and guard rail are intended to steer and “guide” vehicles back onto the road.
Can you use a DeWalt circular saw on a track?
The DWS5022 is a reversible 1.5 metre track for use with the DWS520 plunge saws, as well as other DeWalt circular saws and routers. It features a support rail which runs up the middle and distributes weight effectively to deliver an accurate cut.
Is a plunge saw the same as a circular saw?
A plunge saw is like a circular saw with a blade that spins and cuts, only with much more sophistication and accuracy. Rather than the guard retracting to expose the blade when cutting, such as with a circular saw, it has a fixed guard and the blade is exposed when plunging the handle to the pre-set depth.
How do you cut straight with a circular saw without a guide?
To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
