Im new to circular saws and find that I tend to wobble off the line. The thickness of the guide can reduce the depth of cut if the saw motor gets in the way. No doubt my lack of experience, coupled with only one hand on the saw and the other hand on the square either of which or both may have moved a bit resulting in a dodgy cut.
I have now cheap drill, cordless drill, press drill, jig saw and circular saw and few other bits and pieces. All cheap saws I saw have a pathetic fences and so much play that it would be hard to achieve anything better than with circular saw. I’ve also seen some projects on youtube, good and bad, about turning circular saw into table saw.
circular saw guide bunnings Related Question:
Is there a guide for a circular saw?
A circular saw guide rail is a critical tool for making straight cuts on large boards, but choosing the best one for your workshop is not easy because there are many brands available, and a lot of newer woodworkers aren’t sure how to tell the difference from one brand to the next.
Which square is the best one to use as a guide for a circular saw?
A Speed-brand layout square is a handy guide for making straight crosscuts with a circular saw. Just hook the square’s lip on the edge of the lumber nearest to you and run the saw’s shoe along the square’s edge as you make the cut.
Can you use a circular saw on a track saw guide?
There are retro-fit products available that turn your circular saw into a track saw. They also work pretty well, but they don’t fit perfectly and have some slop (move side to side enough to change the cut a bit) in them. Over time the edge becomes uneven and it’s hard to line the track up.
Are guide rails universal?
The YouTool Guide Rail is universally suitable for almost all brands of saw, and is available up to 5 meters long.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
Does DeWalt circular saw fit guide rail?
The DWS5022 is a reversible 1.5 metre track for use with the DWS520 plunge saws, as well as other DeWalt circular saws and routers. It features a support rail which runs up the middle and distributes weight effectively to deliver an accurate cut.
What is used to guide the piece through the saw?
A “Push Stick” is: A plastic handle or scrap wood shaped so that you can guide the work piece without getting your fingers near an active blade.
What is the difference between a circular saw and a track saw?
The critical difference is that a circular saw has a long and rectangular rail in the front, unlike its counterpart. A circular saw performs double cuts as the rip cuts and the crosscut, whereas the track saw three. The circular saw has a protective guard, whereas the track saw has none.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
Is it a guardrail or guide rail?
According to the US Federal Highway Administration, “The terms guardrail and guiderail are synonymous, and are used in different regions around the country.” Guide rail and guard rail are intended to steer and “guide” vehicles back onto the road.
Can you use any guide rail with a circular saw?
Obviously, it’s important to check that your circular saw is compatible with the guide rail you’re using, particularly if you’re cutting bevels. The risk you run is cutting into the guide rail itself. The GKS65 GCE’s bevel mechanism always keeps the blade away from the guide rail.
What is a plunge saw used for?
Plunge saws are perfect for making smooth, straight cuts and are often used with a track or guide to improve accuracy. They work when the blade is plunged down to the required depth and engages with the workpiece.
What keeps a track saw in place?
While it cuts, a plunge-cut track saw rides along a stable track, which stays in place thanks to non-slip, non-marring pads on its underside.
How do you cut straight with a circular saw without a guide?
To ensure a straight cut, press the saw firmly against the straightedge as you push it along. Clamp a perfectly straight board or metal straightedge to a sheet of plywood to make cabinet-quality straight cuts.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
