Ensure straight cuts with these two, simple cutting guides. With these two saw guides, you can use your circular saw to make cuts that rival a table saw’s for speed and accuracy. Like the straightedge guide, the crosscut guide is customized to your saw so you can simply line up the edge of the guide with your cutting mark and clamp it.
I planned to replace it once I settled into my new house, but when the time came to build a room divider/bookshelf unit, I decided to build a couple of my own makeshift circular saw guides instead. The guides are compact and store easily. It’s quick, safe and especially useful when you need to cut a sheet of plywood down to size or to rip a long straight edge on a wide piece of lumber to prepare it for further ripping on a table saw. The only difference is that I put a 1 x 2 stop on the bottom, perpendicular to the 1 x 4 guide, which automatically squares the guide across the piece being cut.
Making straight cuts in plywood is super easy when you have a straight edge to guide your saw. How To. See how easy and fast it is to make this Circular Saw Straight Edge Guide. Now you can have both of these cuts done for you at your home center, but if you have another sheet of plywood laying around that still has a straight factory edge on it, or another long straight edge, you can use that.
circular saw guide diy Related Question:
Do you need a guide rail for circular saw?
If you want to make accurate cuts when using a circular saw and do it consistently, you need a guide rail. With these rails, you can control the blade far much better than when cutting without one. When cutting hard lumber, the blade can move unexpectedly, which can affect the cut accuracy.
Can you make a track for circular saw?
Steps: Cut a thin piece of the plywood with the circular saw and attach it to the top of the rest of the plywood using wood glue. Be sure to have excess plywood on both sides of the glue joint. Place the circular saw on one side of the straight edge and cut the excess plywood.
Can I use any guide rail with a circular saw?
Obviously, it’s important to check that your circular saw is compatible with the guide rail you’re using, particularly if you’re cutting bevels. The risk you run is cutting into the guide rail itself. The GKS65 GCE’s bevel mechanism always keeps the blade away from the guide rail.
Are guide rails universal?
The YouTool Guide Rail is universally suitable for almost all brands of saw, and is available up to 5 meters long.
How do you use a circular saw without a table?
Fit your circular saw with an edge guide. Set the depth of the blade accurately enough for it to go through the wood and not cut under the surface. Place the guide on base of the circular saw lines and markings you made earlier on the wood. Ensure that the saw is free to move, and the power cord is not entangled.
What is the difference between a circular saw and a track saw?
The critical difference is that a circular saw has a long and rectangular rail in the front, unlike its counterpart. A circular saw performs double cuts as the rip cuts and the crosscut, whereas the track saw three. The circular saw has a protective guard, whereas the track saw has none.
How many teeth do you need for plywood?
Cross-cutting wood or sawing plywood: Use a 40-tooth to 80-tooth blade.
Why is my circular saw burning the wood?
Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty. If wood pitch resins build up behind the teeth of the blade, the cutting speed will slow down, increasing the chances for burns. Commercial blade cleaners are sold for this purpose.
Can a circular saw cut a 4×4?
Circular Saw. A circular saw is one of the best means of cutting a 4×4 post. Most people own a circular saw, its portability makes it easy to cut 4x4s from the ground, and they can make precision cuts by using a relatively simple trick.
Which cut is when you cut a straight 90 degree across the grain?
A crosscut is a straight, 90-degree cut that cuts across the grain of the wood. Usually, that means turning long boards into shorter ones. On a table saw, you will usually use a miter gauge to make crosscuts. It’s the most basic cut you can make.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
