If you need to cut workpieces that must be cleanly and accurately joined together, a circular saw and a guide rail is the way to get this done. Clean, accurate cuts over and over are possible when using a guide rail. The saw is also compatible with other makes of guide rail.
This circular saw guide fits with any circular saw and makes cutting wood easy and precise. The circular saw guide was made for the Japanese market where carpenters and woodworkers still use the old measuring units. Width of workpiece 450 mmCross section of guide 82 x 6 mmWeight 1100 g. SHINWA Circular Saw Guide 45 cm with 90°-Angle.
circular saw guide rule Related Question:
Is there a guide for a circular saw?
A circular saw guide rail is a critical tool for making straight cuts on large boards, but choosing the best one for your workshop is not easy because there are many brands available, and a lot of newer woodworkers aren’t sure how to tell the difference from one brand to the next.
Do you need a guide rail for circular saw?
If you want to make accurate cuts when using a circular saw and do it consistently, you need a guide rail. With these rails, you can control the blade far much better than when cutting without one. When cutting hard lumber, the blade can move unexpectedly, which can affect the cut accuracy.
What is the first rule of using the circular saw?
What should you do before start cutting with a circular saw? Wear safety glasses or goggles, or a face shield (with safety glasses or goggles). Wear an approved respirator or dust mask when exposed to harmful or nuisance dusts. Use appropriate hearing protection equipment in noisy areas.
What is a rip guide on a circular saw?
The Rip-Cut easily makes straight, accurate, repeatable cuts without measuring, marking, or having to keep the saw on the cut line. The Rip-Cut does this with a long edge guide that follows the straight edge of the sheet you are cutting.
How do you measure the offset on a circular saw?
Mark the cut line onto the workpiece, then measure the distance from the circular saw blade to the edge of the saw shoe. That will be the offset dimension. Measure over from the cut line the offset dimension and make a second mark.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
Can you use a DeWalt circular saw on a track?
The DWS5022 is a reversible 1.5 metre track for use with the DWS520 plunge saws, as well as other DeWalt circular saws and routers. It features a support rail which runs up the middle and distributes weight effectively to deliver an accurate cut.
Which way should the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How do you cut a perfect straight line in wood?
You can use both a jigsaw or a circular saw to cut wood in straight lines, but you will get the most accurate cuts, by using the circular saw. Nevertheless, the jigsaw is very versatile if you use the right cutting techniques.
Which side of the line do you cut?
In most cases, we recommend cutting to the outside of the line. You can always take more wood off, but you can’t get it back once you’ve started your cut. The saw blade should move just along the side of the line. If you cut to the pencil line, the thickness of your blade might take off more material than you expected.
How do you square a circular saw board?
Making perfectly square crosscuts with a circular saw is easy, if you guide the saw with a layout square (a framing square or Speed Square will work). Hold the saw in place with its blade right on the cut line. Then slide the square against the saw’s base plate, and press it tightly against the edge of the board.
Can a 5 1/2 inch circular saw cut a 2X4?
Yes! A 5.5 inch circular saw blade is perfect for cutting a 2X4. The blade capacity is deep enough to make a crosscut in 1 stroke. If you want to make a 45 bevel cut then you will need to make 2 strokes.
Are track saws worth it?
Conclusion. A track saw is unbeatable when it comes to making long, accurate cuts. It can do most things a table and circular saw can, while being more portable than a table saw and more accurate than a circular saw. It’s also better than a table saw at breaking down large sheets of plywood.
What is a guide saw?
One of the easiest ways to up your game when it comes to DIY and woodworking projects is to use a saw guide when cutting with your circular saw. This is a super simple way to make sure every line you cut is straight as an arrow, which means you’ll waste less time and material dealing with uneven or inaccurate cuts.
What is the difference between a cross cut and a rip cut?
The Crosscut blade is used when cutting short grain, while the Ripping blade is for long grain. The Combination blade allows one to cut both crosscut and ripping using the same blade.
