Milwaukee has released its M18 Fuel Rear Handle Circular Saw as well that comes with a MASSIVE 12 amp hour battery. Because of the placement of the motor, Rear Handle Circular Saws get a heck of a lot more torque than a standard Sidewinder Circ Saw. Rear Handle Head To Head. In the video above you get a look at the two beasts of the cordless rear handle circular saw segment.
Bring the saw up to full speed, lift the guard, and slowly push the body of the saw down to start the cut. TIP: Make sure to start back far enough so that you only push the saw forward; never drag a spinning saw back. If a board is too wide for the saw shoe to hang over the edge during a rip cut, hold a narrow scrap of wood between thumb and forefinger, bracing your finger along the edge of the board, and butt the saw shoe against the edge of the wood scrap as you push both along the board.
While sidewinder circular saws and worm drive circular saws perform the same function, there are some important differences. You’ll usually find worm drive saws at about 4,250 RPM while direct drive saws carry speeds of 6,000 RPM or higher. We hope you’ve enjoyed this article about Sidewinder Vs Worm Drive Circular Saws.
With a few test cuts pretty sure I will like the saw. Either way it was pretty much free with the deal.249.00 total for 4 batteries, dual charger and saw. If I had still been used to my Makita 71/4″ electric.
Because of the placement of the motor, Rear Handle Circular Saws get a heck of a lot more torque than a standard Sidewinder Circ Saw. Most any circular saw with sufficient power and fitted with a good blade will do adequate cutting, but for long-term satisfaction, you may want to look for these features: Saw foot made from cast magnesium rather than pressed steel. The 18V Brushless Lithium Ion 6-1/2 Inch Deep Cut Circular Saw is a revolutionary cordless circular saw utilizing a 6-1/2″ blade which allows a 2-19/32″ cutting depth, making it one of the deepest cutting cordless circular saws on the market.
circular saw rear handle vs top handle Related Question:
Is a rear handle circular saw better?
Because of the placement of the motor, Rear Handle Circular Saws get a heck of a lot more torque than a standard Sidewinder Circ Saw. Sidewinders get more RPM’s, but the torque and power beats speed when you’re cutting into hardwoods with a Worm Drive (rear handle) saw.
Why are worm drive saws left-handed?
Traditionally, all worm drive saws operated in a blade-left orientation. Furthermore, this orientation likely places the weight of the saw over the portion of the material the user wants to keep, making it easier to stabilize the saw during the cut.
Is it okay to cut wet wood with a circular saw?
If you’re cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you’re cutting. This will stop your saw and cut line from getting clogged with wet saw dust.
Which is better worm drive or circular saw?
Worm drive saws offer more durability and power because they have larger teeth which have a more loading capacity than regular circular saws. This feature enables the user to handle loads with high shock. It can handle tougher projects because it has great muscle to pitch cut.
What size circular saw will cut a 4×4?
Cutting a 4×4 with a Circular Saw – Guide If you need to cut a 4×4 post, then the ideal tool is a large 12” miter saw. This saw has the blade diameter needed to chop through a 4×4 in a single pass, so if this is an option for you it’s the way to go.
What should I look for when buying a circular saw?
The main things you should be looking out for when choosing a circular saw are cutting capacity, cutting depth and bevels. The capacity and depth of your cut with a circular saw is based on the size of the saw’s blade.
Is a circular saw the same as a skill saw?
Circular Saws vs. All skill saws are circular saws. They all have circular blades that spin rapidly to bite through wood. However, not all skill saws are circular saws. Circular saws can be gas-powered, have sidewinder or hypoid designs, or even be fixed to radial arms, which skill saws commonly aren’t.
What is the advantage of a worm drive circular saw?
Advantages of a Worm Drive Circular Saw The longer distance between the handle and the blade extends your reach while making a cut, which is helpful for crosscutting sheet goods. A worm drive also has larger gear teeth with more load-carrying capacity than a direct drive, which provides more power but also adds weight.
Does Dewalt have a left-handed circular saw?
This 7 1/4″ saw is just a cordless version of the corded right side sidewinder. And Dewalt makes a left side blade circular saw that is basically a cordless worm drive if you need that bid of a saw to have the blade on the left side. 2 of 2 found this helpful.
Does a circular saw need to be oiled?
The saws can cross-cut and rip cut. They also can be set to bevel cut and pocket cut. The blade doesn’t need to be oiled very often; you can coincide the oiling with blade replacement, but a spot of oil on the inner washers will keep the saw running better and more safely.
Which way should the teeth face on a circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
How many amps do you need for a circular saw?
For corded circular saws, the power rating is generally expressed in amperage. Today, 15-amp saws are the standard; 10- or 12-amp saws are appropriate only for infrequent use.
Should you let pressure treated wood dry before building?
The first tip for working with pressure-treated lumber is to let it dry before using it. Other woods such as redwood and cedar are dry when you buy them. But lumber that has been treated has been injected with massive amounts of chemicals and water.
Can I leave pressure treated wood in the rain?
While the chemicals in pressure treated lumber prevent rot and ward off insects, they don’t prevent moisture from seeping into the wood. On a deck that’s going to be directly exposed to rain, water can seep into the boards and cause them to swell. As they dry in the sun, they’ll shrink.
Is it better to cut wood when it’s wet or dry?
Wet Wood Vs Dry Wood But wet wood is actually much easier to cut than dry wood. With dry wood lacking moisture content, more friction is created as the chainsaw chain comes into contact with the wood fibers. This friction results in the chain slowing down.
