The term “Power tool” in the warnings refers to your mains-operated power tool or battery-operated power tool. D) Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. WARNING: The vibration emission value during actual use of the power tool can differ from the declared value depending on the ways in which the tool is used dependant on the following examples and other variations on how the tool is used: How the tool is used and the materials being cut or drilled.
ALWAYS keep your body positioned to either side of the saw blade, but not in line with the saw blade. Indle ustment Knob Scale Blade Wrench Storage Area 11 UNPACKING Your circular saw has been shipped completely assembled, except for the blade, which is packed unassembled. Heavy load on the saw blades on hand, so sharp hardened on the blade hot water or kerosene to BLADE GUARD SYSTEM The lower blade guard, attached to your circular saw, is there for your protection and safety.
circular saw user guide Related Question:
Which side should the blade be on a circular saw?
For blade-right models, the correct circular saw blade direction is usually with the label side out. For saws that have the blade on the left, it typically installs with the “ugly” side out.
Are guide rails universal?
The YouTool Guide Rail is universally suitable for almost all brands of saw, and is available up to 5 meters long.
Is it okay to cut wet wood with a circular saw?
If you’re cutting wet wood set the depth so that the entire gap between the teeth is clear of the board you’re cutting. This will stop your saw and cut line from getting clogged with wet saw dust.
How do you use a circular saw without a sawhorse?
In some cases, it might be better to use your circular saw without a sawhorse. If you need to make cuts without a work support, you can lay a sturdy, stationary surface under the material while making cuts.
What size circular saw Do I need to cut 2×4?
You need a minimum 5-3/8 inch size circular saw blade to cut a 2X4 at a 90 degree angle in one cut which is a crosscut. If you want to cut a 45 degree bevel with this size circular saw it will take 2 cuts. You could go with a 7-1/4inch or 10 inch blade to avoid making multiple cuts with the 45 degree bevel angle.
Why does my circular saw burn the wood?
A dull blade will make it hard to cut quickly, and the slower the feed rate of the saw, the more friction against the wood and the greater the likelihood of scorch marks. Pushing the stock through the saw too slowly is a common cause of saw blade burn. Sometimes a blade that feels dull might only be dirty.
What does more teeth on a circular saw blade create?
The number of teeth on the blade helps determine the speed, type and finish of the cut. Blades with fewer teeth cut faster, but those with more teeth create a finer finish.
Which way should teeth face on circular saw?
The teeth should be cutting UPWARDS, in a clock-wise direction. You’ll also notice that when your blade is installed correctly, the teeth will be pointing upward. Remember: circular saws (as most saws) cut on the upward stroke.
Why are so many circular saws left-handed?
The placement of the cordless saw blade, on the left side, gives you a clearer line of sight when you cut. The reason for this is because the main bulk of your circular saw is not blocking your view. Cordless circular left-handed saws provide you better movability.
Do all circular saws rotate the same direction?
Circular Saws This means that the circular saw cuts wood on the upstroke. For a right handed circular saw (most common), this means that the blade rotates counterclockwise, which is similar to the table saw. For a left handed circular saw, the blade rotates clockwise.
Can I use any guide rail with my circular saw?
Obviously, it’s important to check that your circular saw is compatible with the guide rail you’re using, particularly if you’re cutting bevels. The risk you run is cutting into the guide rail itself. The GKS65 GCE’s bevel mechanism always keeps the blade away from the guide rail.
Can you use Makita circular saw on guide rail?
Enables use of DHS680 Circular Saw with the Makita guide rail system. This adaptor can be attached to Makita circular saws, which allows you to use the circular saws with the Makita SP6000 guide rail system for precise, straight routing cuts.
Can I use my circular saw as a track saw?
A circular saw can be used for all the same functions as a track saw, but doesn’t necessarily do them quite as well. If you’re on a budget, you can turn your circular saw into a makeshift track saw with straight edge guide. You can make your own circular saw jig, or buy one instead.
Whats the difference between a circular saw and a skill saw?
Circular Saws vs. All skill saws are circular saws. They all have circular blades that spin rapidly to bite through wood. However, not all skill saws are circular saws. Circular saws can be gas-powered, have sidewinder or hypoid designs, or even be fixed to radial arms, which skill saws commonly aren’t.
