You may have heard about trim saws and farming saws and wonder what is the difference between these two types of portable circular saws. Trim saws are the smallest saws available, so every saw with a blade smaller than 6 inches is considered as a trim saw. Similar to the case with the trim saw – for crosscuts and mitter cuts, it is better to use a mitter saw and for rip cuts it is better to use a cabinet or hybrid table saw, but the framing circular saw will do the task better than a trim saw.
Bring the saw up to full speed, lift the guard, and slowly push the body of the saw down to start the cut. TIP: Make sure to start back far enough so that you only push the saw forward; never drag a spinning saw back. If a board is too wide for the saw shoe to hang over the edge during a rip cut, hold a narrow scrap of wood between thumb and forefinger, bracing your finger along the edge of the board, and butt the saw shoe against the edge of the wood scrap as you push both along the board.
Framing blades are probably one of the most popular types of blades out there and some of the most commonly used blades out there, so chances are you will see these in stores more than any other type of blade. Typically a common “Framing” blade will have about 18 – 24 teeth on it or somewhere close to that number. A general rule is that the greater the number of teeth on a blade, the cleaner and smoother the cut will be.
circular saw vs framing Related Question:
What saw to use for framing?
A circular saw is the go-to tool for cross-cutting and ripping framing members and sheet stock like plywood.
What are the advantages of using circular saws?
Among many advantages of the circular saw is its simple efficiency. Unlike the reciprocating saw, which cuts only half the time (each cutting stroke is followed by a return stroke), the circular saw is ready to cut whenever its blade is in motion.
Can a circular saw be used on a wall?
Gravity-Fed Sawing. At some point, you may need to make a long, straight, vertical cut into a wall, and the circular saw is right the tool to use. Just remember to start the saw at the top of the wall and cut down.
What’s better than a circular saw?
A miter saw is safer to use than a circular saw. A circular saw can make both rip cuts along the length of a board and cross cuts across the width of a board, but a miter saw can only make cross cuts.
What saw should I buy first?
A jigsaw is great for cutting curves and shapes, and it can also be used with a guide to make straight cuts, which is why this is the first power saw you should own. Unless you plan to rip long sheets of plywood, a jigsaw is preferable over a circular saw.
Which saw is most versatile?
The table saw, in my opinion, is the most versatile tool in the shop and should be your first major purchase. Next up is the Miter Saw. The miter saw does one thing but it does it really well. The Miter saw will cross cut wood better and faster than pretty much any other tool.
What is the disadvantage of circular saw?
Compared to jigsaws, the main disadvantage of circular saws is that they can’t cut curves – they are designed to cut in straight lines only. The blades for circular saws are more expensive – although, as we mentioned, they last longer so won’t need to be replaced as often. They are big, noisy tools.
What were the drawback of circular saws?
Disadvantages of the circular saw: The main disadvantage of the disc saw is that it is more dangerous than other power saws such as the jigsaw or the saber saw. Another disadvantage is that the disc saw only serves to make straight cuts, so it is not as versatile as a Jig Saw.
How do I make an accurate cut with a circular saw?
Using a Straightedge for Accurate Circular Saw Cuts Measure the exact distance from the edge of the circular saw’s shoe to the same side of the blade. Once you have that measurement, add it to your original marks and make a new line. Set the straightedge on the new marks, clamp it down, and make your cut.
Can I use circular saw to cut drywall?
First, don’t use a circular saw to cut drywall. It’s like using a rock to hammer nails. Both are the wrong tools for the job. A circular saw creates giant clouds of unnecessary dust.
Can I use a wood saw to cut drywall?
Just guide the saw along the framing while holding the saw square to the drywall face. To avoid breaking the drywall edge and tearing the face paper pull back gently and only cut on the push stroke. This is the same thing you would do when cutting wood with a hand saw, you only cut on the push stroke.
Can you use circular saw on plasterboard?
Place the guide rail according to the scribe mark and secure it tightly using the fastening clamps if necessary. Connect the portable circular saw to the dust extractor. Set speed level 1 to 3 on the circular saw. Switch on the tool and cut the plasterboard at a moderate feed rate.
Can I use a jigsaw instead of a circular saw?
Although a jigsaw can be used for most of the tasks that a circular saw can perform, including straight cuts and cuts on a tilt, the jigsaw uses that really take advantage of the tool’s qualities are jobs such as kitchen fitting and joinery, with their frequent need for complex cuts.
What’s the difference between a skill saw and a circular saw?
All skill saws are circular saws. They all have circular blades that spin rapidly to bite through wood. However, not all skill saws are circular saws. Circular saws can be gas-powered, have sidewinder or hypoid designs, or even be fixed to radial arms, which skill saws commonly aren’t.
Are cordless circular saws worth it?
This saw differs from the others in several ways. It takes two 18V batteries and delivers awesome power and exceptional run-time. Of all the saws we tried, it performed most like a corded saw. It’s also large and heavy, making it a great tool for big, tough jobs, but maybe not the best choice for standard duty.
