It actually sounds like it is your trigger or switch since it is not doing anything at all. If you do not feel comfortable pulling of the guard and checking with a power meter, then just wait and talk to Dewalt tomorrow.
Make sure the saw is turned off, then loosen the depth adjustment knob and raise the flat metal bottom piece until one tooth of the blade extends under the piece you wish to cut. If you are trying to cut at a 90 degree angle but it keeps coming out as a more acute angle(>) turn off the machine, then try loosening the knob by the front of the saw blade. To tighten the blade, screw the washers in the center of the blade clockwise using the blade wrench.
dewalt band saw not working Related Question:
Why is my bandsaw not working?
A bad power supply, broken power cord, failed on/off switch or bad drive motor can prevent the band saw from starting. Check the power supply first. Plug a shop light or other electrical tool into the electrical outlet that you’re using for the band saw to make sure the outlet works.
What is a deep cut band saw used for?
The Deep Cut Band Saw has one basic purpose: making clean, straight cuts—and it does this very well. Since I first used the saw to cut steel bar stock, I’ve also cut steel and PVC pipe, steel tubing, conduit, and aluminum bar stock.
What size blade does a Dewalt portable band saw use?
14 TPI Portable Band Saw Blade (. 020″ 3 pack) | DEWALT.
Why is my bandsaw blade twisting?
The difference between the steak and the bandsaw is where the steak knife is short and thick, the bandsaw blade is generally long and skinny. This becomes a problem because it is possible to push hard enough on the blade to cause it to twist left or right.
Is a portable band saw worth it?
What to Consider When Choosing Portable Band Saws. The portable band saw is one of the few tools that, when used with the right blade, is equally effective regardless of material. It can cut straight lines or curves, so it can be used for joints, precision cuts, or decorative work.
How long does a portable band saw blade last?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
Are Dewalt and Milwaukee bandsaw blades interchangeable?
Blade. If you’ve used any type of power tool, you’ll be well aware of the importance of the blade, and keeping it maintained properly. The Milwaukee 2429-21 XC compact bandsaw allows for blades up to 32” to be used, and the DeWalt DCS317B can take a blade with the sizing of 27 ½”.
Are band saw blades interchangeable?
For cutoff work, band saw blades should be as thick as the saw and material will allow. TPI stands for “teeth per inch” when talking about band saw blades. “Pitch” is interchangeable with TPI when talking about band saw blades.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
What causes bandsaw drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
What is the throat on a band saw?
The throat is the distance from the blade to the vertical frame section of the body of the saw. This distance determines the width of cut that can be completed on the band saw. The throat on a free-standing cabinet band saw typically exceeds the 12 to 14-inch throat of smaller, bench-top models.
What speed should you cut metal with on a band saw?
To cut steel, you’ll need to run the machine at a much slower speed — about a hundred feet per minute. A machine running at this speed might look like it’s running too slowly, but running it any faster almost guarantees that you’ll damage the blade.
What size blade does a Dewalt DCS371 take?
What’s in the box. DCS371 20V MAX band saw, 14/18 TPI blade, blade tracking wrench, battery and charger sold separately.