A chainsaw has a saw kerf right around 3/8 of an inch, which means it is very inefficient and produces a lot of sawdust. For these reasons, a chainsaw mill is definitely not to be used for optimizing the amount of lumber that you can yield from a log.
Chainsaw mills are small sawmills designed to be used by just one or two operators to mill logs into lumber. More elaborate chainsaw mills consist of a track and frame system to which the chainsaw is mounted. For these reasons, a chainsaw mill is definitely not to be used for optimizing the amount of lumber that you can yield from a log.
If you do not need a large-scale sawmill, there’s absolutely no need to spend more money on one and you would be better off with a chainsaw mill. In order for you to be able to fit your chainsaw into the sawmill, it must be compatible or else it won’t fit. Before you proceed with purchasing a sawmill, you need to make sure that your chainsaw and the sawmill are actually compatible, unless you plan on purchasing an additional chainsaw.
The chainsaw mill is a long tiring way to work( I know) I picked up a used band mill for $2500, it will cut 17′ long, sits on a trailer so I can haul it to and thru my bush. Chainsaw mill,good for breaking down huge logs,that are too big for other mills…. I have a chainsaw mill from Granberg. If I had my choice I would use the bandsaw mill everytime but alot of the time it is more convinient to use the chainsaw mill.
Like we stated in the intro, chainsaw mills aren’t worth it for four reasons: labor, cost, time, and waste. I know I’ve been pretty critical of chainsaw mills up to this point, but there is one reason why a chainsaw mill could be worth it. Chainsaw mills aren’t worth the physical and time demands required to mill the logs.
do chainsaw sawmills work Related Question:
Is chainsaw milling worth it?
A chainsaw mill is one of the most efficient and effective tools when it comes to converting wood into lumber. Lumber is a very effective raw material that can be used for a variety of purposes. Be it for firewood or be it for construction purposes, you can certainly utilize lumber for whatever you need.
Can you mill with a chainsaw?
The most critical tool is obviously a chainsaw. In the world of chainsaw milling, the more powerful the saw the better. You can mill with a smaller saw; however, it’s going to be really slow. On average, it takes me about 10-15 minutes to make one cut using my saw, based on the size logs that I typically cut.
Is milling wood worth it?
Milling your own lumber can produce quality material for a fraction of the price of a lumber dealer. In fact, if you purchase your own mill, like I have, you can actually make a profit off of it by selling lumber to other woodworkers and by offering to mill other people’s logs.
How fast does a chainsaw mill cut?
Cutting speeds can vary from 8 feet a minute in narrow softwoods, to 1-1/2 feet a minute in wide hardwoods.
Is it cheaper to mill your own wood?
In the end, only you can decide if milling lumber from your own property is worth it. Because every job is different, we can not tell you the actual amount of money you would save or not save. Generally, it costs 5-10% more to have your lumber milled on-site.
Is it cheaper to buy lumber from a sawmill?
Though it may not appear bad, the cost of lumber in big box stores is VERY expensive. You don’t realize it because you don’t have anything to compare it to. Buying your lumber directly from a sawmill can be significantly less, though there may be additional preparation needed before it can be used as we will see below.
How much does it cost to have lumber milled?
By the Board Foot Pricing varies by species and location but ranges from $0.25 to $0.50 per board foot of sawn lumber.
What is a ripping chain?
Ripping chain is chainsaw chain designed specifically for cutting with the grain. Ripping chain is always micro chisel or semi chisel chain which features a re configured cutting angle of 10 degrees.
How long does it take to mill a log?
The time/cost to saw the logs depends mostly on the log’s size and species. As a very rough estimate, a 12″ diameter 8 foot long log will take around 25 minutes; an 18″ diameter 8′ long log will take around 40 minutes to saw; 24″ diameter will be at least 1 hour.
How big of a chainsaw do I need for an Alaskan mill?
Most Alaskan mills require at least 3 inches extra at the end of the bar for attachment. I also recommend going with a saw with an engine size of at least 60cc for smaller logs and softer woods. A minimum of 90cc would be best though.
Are portable sawmills worth it?
A portable sawmill can be worth the investment. It can provide a source of wood for your own projects and give you a side business. For a source of lumber, as well as a profitable business, a portable sawmill can be a key piece of equipment on your farm.
What is a chainsaw guide bar?
Guide bars provide precise guidance to the chainsaw with minimal friction loss. They have to take on the toughest jobs without warping. The two basic types − the Rollomatic and Duromatic − have been designed to handle different requirements and areas of application. Rollomatic bars are ideal for everyday use.
Can a chainsaw cut metal?
To answer your question: “Can a chainsaw cut through metal?” The answer is yes, a chainsaw can cut through metal. Chainsaws are multi-purpose machines that can be used in a variety of situations.
Can I use my chainsaw to cut concrete?
The hydraulic-powered Lynx LCC31 concrete cutting chainsaw from Stanley Hydraulic Tools will cut concrete (wire or rebar reinforced), brick, block, masonry and stone. It can cut square corners for openings and wall cut-outs, as well as plunge cut into walls and make full-depth cuts at one pass.
Can a chainsaw cut a 4×4?
While the best way to cut through a 4×4 is by using a 12-inch miter saw or a 10-inch radial saw or slide saw, those tools aren’t always readily available. With a little ingenuity, it’s possible to make precision cuts with other tools, including circular saws, reciprocating saws, chainsaws, and even handsaws.