To work properly, chainsaw chains and bars must be lubricated.In the past, most operators have used petroleum-based oils. When a chain saw is used, virtually all of the lubricant ends up in the environment. Every year thousands of gallons of chain-and-bar oil are carried into the forests and none returns.
Most high quality or professional chain saws have sophisticated chain oilers that are more efficient and have the capability of controlling the amount of oil being used. FERIC STUDY The Forest Engineering Research Institute of Canada tested and reported on field trials of a vegetable-based oil for lubricating chain saws. Rottne harvester operators noticed a significant reduction in the oil mist that collects on the machines windows due both to the cleanliness of the Binol compared to petroleum-based oil and to the reduced consumption of oil.
The reason a special type of chainsaw bar oil exists is that chainsaw chains and bars need a lubricant with certain qualities to keep those parts running smoothly. Motor oil will work to keep your chainsaw from burning up if you don’t have any standard bar oil on hand. Hydraulic oil is similar to motor oil and you can use it as a chainsaw bar oil substitute when you have nothing else available.
At Gardening Products Review, we highly recommend oil manufactured for this specific use. Chainsaw shown in this video tutorial is the Redback 40V 12″ Li-Ion Cordless Chainsaw. The bar & chain oil featured in this video is Husqvarna Bar & Chain Oil – 1 Gallon.
The answer is yes, there are – so here, we look at some of the possible chainsaw bar oil substitutes. It is thinner than regular vegetable oil, meaning it will tend to fly off the chainsaw more quickly – but it has a more suitable viscosity at lower temperatures so makes a good substitute for chainsaw oil when it is too cold to use vegetable oil. This is a sure sign that your chainsaw is not lubricated, so you should check you still have oil in the reservoir and consider trying a different oil if the oil you are using isn’t doing the job.
do you need chainsaw bar oil Related Question:
Is chainsaw bar oil necessary?
You want lubrication of the actual chain against the bar. You don’t want to chain to burn – which is what might happen if there’s too much friction. Without oil, it causes frictional force on the motor in the chainsaw as well.
What happens to chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
What’s the difference between chainsaw bar oil and regular oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can you start chainsaw without bar?
It is not recommended to run a chainsaw without a chain. If you need to run it as a movie prop or you are fixing the engine, ensure that you run it for a short time only. I do not recommend letting it run for more than 5 minutes. Without a chain, the chainsaw will cause the engine to rev higher.
Can I use WD40 as chainsaw oil?
No. You should never use WD40 as chain lubricant since WD-40 is NOT a true lubricant. WD40 is primarily a solvent or rust dissolver.
Is it OK to use motor oil instead of bar oil?
If your manufacturer’s bar and chain oil is unavailable, you can use SAE 30 weight motor oil to lube your chain during the summer and SAE 10 weight during the winter, according to the University of Missouri Extension.
Can I use 5w30 for chainsaw bar?
Can I Use 5w30 for a Chainsaw Bar? Like 10w30 motor oil, you can use 5w30 oil. However, the thin and low-viscosity SAE5 weight oil will not cling to the chain and chainsaw bar very well in the summer. You may experience a lot of oil loss and a messy worksite if you choose this chainsaw bar oil alternative.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
What is special about chainsaw oil?
Chainsaw bar oil has a certain level of “slickness” to it. This slickness keeps the chain spinning at a fast rate without getting slowed down by the friction that occurs when metal rubs against metal. So, if you want to use the “correct” type of bar oil in your chainsaw, consult the manual and use what it suggests.
Can I use used motor oil for chainsaw bar oil?
If you really want to run it I would recommend running it through some sort of filter first as often times used motor oil has bits and pieces in it that can and will clog up the tiny passage in your chainsaw oiler. Won’t mention that used oil usually contains heavy metals and is slightly toxic….
Can I use cooking oil for chainsaw?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Does a Stihl chainsaw need oil?
Stihl gasoline-powered equipment uses a 50:1 ratio of gasoline and 2-cycle engine oil. Learning how to mix your fuel properly is important in keeping your chainsaw in excellent condition over time.
How often should you oil a chainsaw?
The chain saw should be oiled before each cut. For Manual Oiling System: Lubricate the saw chain by pressing the bulb on the oil reservoir cap twice before making each cut. Hold the bulb down for 3-4 seconds on each press. Automatic oiling system will keep the bar and chain constantly lubricated.
What can I do with an old chainsaw?
Gas and oil can be disposed of at a household hazardous waste collection site for free. Remove non-metal parts and place in the trash. Metal parts can be recycled as scrap metal.