Or, if your thrust bearing is too far past the blade, more toward the center of the bearing than the edge, then it won’t turn and you’ll get sparks too, and possibly wear a groove in the bearing. You want the blade right at the edge of the thrust bearing’s edge, enough so that it contacts the bearing in such a way that it’s downward movement will start the bearing turning as it is touched by the back of the blade, but not enough so that the back of the blade wants to slip off and past the edge of the bearing – the Goldilock’s zone. 12-13-2016, 10:11 PM #11 Not sure what if any guides Carter makes for the S45 but if they only make their 2000 series “Skateboard” bearing guides for it then it would be a downgrade now if they make Guidall or Micro-Precision guides for it then it would be at least a lateral move on the side guides but an upgrade on the thrust bearing.
I back out all the guides and bearings, then center the blade tracking, then close the gaps on the side guides above and below the table, then check for square with table, then bring the thrust bearings to a distance very close to the blade, then when I am sure everything is right I turn it on and look for blade flutter… if there is fluttering I add more tension. The thrust bearings should not touch the back of the blade when it is just freewheeling, only when there is a heavy thrust like when re-sawing. Another thing to be aware of is that when you are thrusting the blade into the thrust bearings that the side guides do not contact the blade set.
“I’m using a 1/4″ blade on my bandsaw and trying to cut a curve with a radius of 3.75”. You should be able to cut a much tighter radius with a 1/4″ blade so I dont think that is the problem. Have your say… Forum Topics Woodworking Skill ShareYour woodworking skills are displayed for several lifetimes in each project.
A quick Google search will reveal the popularity of both the metal circular saw and the portable band saw. Because it’s a burning question, we decided to write up a blog post today to explain the differences between a metal circular saw and a portable band saw. A metal circular saw is a saw that is designed for ,well, cutting metal.
On to the problem…. With the saw, I ordered Laguna’s ceramic guide block set. While sawing away, I noticed sparks coming from the upper guide bocks. FYI, be sure torotate the rear guides fairly often in order for them to wear evenly.
does a bandsaw create sparks Related Question:
Is a bandsaw safe?
The band saw is widely regarded as among the safest of all woodworking machinery. However, it is still a dangerous woodworking tool, one that can cause considerable injury if used improperly.
What should you not do with a bandsaw?
Safety Rules Never adjust saw or setup while saw is running. Never cross arms. Always follow 4 inch rule. Never push on back of piece with fingers or thumb.
What causes bandsaw vibration?
A common source of vibrations on commercial bandsaws is that the wheels are not quite round, or at least slightly off center. This is often caused by tires that weren’t evenly stretched when they were put on.
Do band saws have kickback?
Don’t feed the stock too fast into the band-saw blade. If you do, the blade will chatter, cutting unevenly. (Don’t go too slowly, either, or the blade will tend to burn the workpiece.) There’s essentially no risk of kickback, however, as the motion of the blade tends to drive the work-piece against the worktable.
What does the bandsaw do?
A bandsaw (also written band saw) is a power saw with a long, sharp blade consisting of a continuous band of toothed metal stretched between two or more wheels to cut material. They are used principally in woodworking, metalworking, and lumbering, but may cut a variety of materials.
Can you rip wood on a bandsaw?
A band saw can shape curves, saw rough lumber safely, cut joinery, and even rip boards to width.
Is a band saw safer than a table saw?
Since the blade is so narrow and it cuts downward, it has the advantage of essentially keeping the workpiece solidly on the table as you make the cut. This makes the bandsaw inherently safer than a table saw for most cuts. Making a rip cut on the band saw is a breeze, with the right blade.
What personal protective equipment should you wear while using a band saw?
What safety procedures should you follow when using a band saw? Wear safety glasses or goggles, or a face shield (with safety glasses or goggles). Wear hearing protection that is suitable for the level and frequency of the noise you are exposed to in the woodworking area.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
What is the purpose of a push stick?
Push sticks or push blocks should be used when operating standard woodworking machinery, including table saws, band saws, radial arm saws, jointer/planers and shapers. These sticks protect the hand while allowing good hand control of the stock as it is pushed through the cutting head or blade.
What kind of stock should not be cut on a band saw without a V block or holding jig?
Don’t cut stock that is not flat on the bottom without a jig. 4. Keep a balanced stance at the band saw. 5.
When operating a band saw which of the following is a safe practice?
Keep guards in place at all times. The blade guard should be from 1/8 to ¼ inch above stock. Keep hands away from blade and do not open upper or lower bandsaw doors while blade is in motion. Maintain a balanced stance and keep your body under control at all times; do not overreach.
How is the band saws size determined?
The Specs. A bandsaw is nominally sized by the diameter of its wheels. The throat width is then immediately recognizable as about 1″ less — that defines the widest board that can be passed between the blade and the column. The resaw capacity is the maximum height (thickness) that can be cut.
Can band saws cut metal?
Band saws are not suitable for cutting very thin sheet metal; a rule of thumb suggests the metal to be cut should be thicker than the depth of 3 band saw blade teeth, however they are excellent for cutting thin walled profiles such as box and angle.
Is a bandsaw necessary?
No, you don’t. As a hand tool woodworker you are fully self sufficient without a bandsaw.