If your bandsaw is close to the lower range, you’ll get a good cut. The general guidelines for bandsaw use to achieve a straight and true cut are not really different from those applicable to other power saws – – table, jig, chop, skill. Sharp blades, proper tension and speed, using a fence for that straight cut and letting the blade do the work will give you what you want, whether it’s simply ripping a thick slab down or making that fancy curve cut on table legs.
On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves. During regular cutting on a well set up bandsaw the blade will move or bow backwards a bit as you press the workpiece into it. The side guides will assist in keeping the blade cutting straight, but they are not an iron lock on the blade forcing it to cut straight.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
This in turn causes the blade to not cut in a straight line. With a dull blade, there is an expectation for it to cut slower and cut crooked. The main thing that normally goes out is the crown, which is what is holding the blade in place, Most of the time the blade is right at the center, but if the crown begins to wear out, it may start allowing more and more movement, causing the blade to not cut in a straight line.
You can change a band saw blade and tension it properly in a couple of minutes. Turn on the band saw and position the pencil line parallel to the blade at the point where the blade should enter the wood. Install a thin, fine-tooth blade that is at least 1/2 inch wide into the band saw.
If the blade twists and the work piece is harder to push through the cutting area, replace the blade. Loose blade tension can also cause the blade to twist and veer off course when cutting the work piece. Check blade tension by pressing in on the side of the blade using a gloved finger.
Test-rip on a piece of scrap, and alternately loosen one machine screw and tighten the other until the fence is parallel to the cutting track of the blade. Have your say… Forum Topics Woodworking Skill ShareYour woodworking skills are displayed for several lifetimes in each project. Show us your jigs, share your tips, strategies and, of c… 1908 Wood & LumberDifferent wood requires different woodworking strategies – from cutting to finishing.
does a bandsaw cut straight Related Question:
Why does bandsaw not cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Does a band saw always cut downward direction?
2. The teeth on the blade of a properly installed bandsaw should point downward in the direction of blade travel.
Why do bandsaws wander?
Tim Inman: Because band saw blades ride on crowned wheels, they always have a little “camber” angle relative to the vertical axis of the wheel. This causes the blade to tip a little and makes the cut “pull” to the side.
Why are my bandsaw cuts wavy?
The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.
Are band saw blades directional?
On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves.
Which way do the teeth face on a bandsaw?
The teeth on the bandsaw blade should face down so that the cutting action is from the top of the material to the bottom.
What causes bandsaw drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
How do you straighten a bandsaw blade?
How to straighten a bandsaw blade? It is risky but if it’s absolutely necessary, a temporary fix to straighten a bandsaw blade can be done by placing it on an anvil and gently tapping it flat with a nylon head hammer/mallet or using a pair of gas pliers to straighten out the blade.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
How tight should a sawmill blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
What does straight cut mean?
Definition of straight-cut : having the leaves cut lengthwise —used of smoking tobacco.