The next iteration of chainsaw oiler was still manual, and because it involved an onboard thumb plunger next to the throttle, it eliminated the need for a “Chainsaw caddy.” This advancement in chainsaw oiling technology allowed the operator to manually pump oil onto the bar while cutting. If the chain spits small amounts of oil onto the wood, you’ll know that your chainsaw oiler is functioning properly. As always, if you’ve got any other pro-tips on how to keep your chainsaw oiler functioning properly, feel free to leave them in the comments section below!
Chainsaw oiler consists of an oil pump, oil lines, and oil holes. With the oiler system cleaned from all the debris and gunk, reassemble everything and start your Chainsaw. For electric chainsaw models, you should examine the oiler after each use and make sure it gets replenished when empty.
In this article I’m going to explain why it’s important to keep the chain lubricated and how chainsaw oilers work. With manual oilers you need to release oil onto the chain, usually by pressing a pump button. Some chainsaws come with automatic oilers which allow you to adjust the flow rate of the bar oil.
If your chainsaw is new or you have replaced your chain and guide bar, you will need to keep adjusting the oiler until you determine the right setting that will enable the oiler to produce just the right amount of lubrication. If the above fixes do not work or oiler problems keep recurring, this could indicate that your oiler may be damaged. To ensure that the oiler is functioning correctly, start the chainsaw and let it run for a few minutes then direct the tip of the chainsaw blade towards a piece of wood.
how chainsaw oiler works Related Question:
Why does my chainsaw use so much bar oil?
What causes a chainsaw to leak oil? As the oil is pumped from the tank through to the guide bar, air begins to replace the space where the oil was previously stored. If there isn’t proper ventilation of the oil tank, a vacuum can occur and reduce the flow of oil to the guide bar.
How do you clean a chainsaw oiler?
Wipe oil and sawdust from the bar, including from the groove in the bar’s rim, by using a rag. Clean the oil feed hole on the bar by poking 16-gauge wire through it. Poke the wire into the oil outlet port on the body of the saw to remove sawdust and dirt that may block it.
Do chainsaws always leak bar oil?
In all but very exceptional cases there is nothing wrong with the chainsaw and what appears to be an oil leak is simply oil that has sprayed from the chain as it rotates at high speed, draining from the saw body and guide bar.
Can you overfill chainsaw oil?
Have you overfilled the oil reservoir? It’s easy to do and it is amazing how many times this simple oversight is the cause of chain oil leaks. An overfilled reservoir can often leak oil when the saw is turned on. Check this and siphon some off if it looks excessively high.
Can you put too much bar oil in a chainsaw?
Technically speaking, you can’t put too much bar oil into the fuel tank of your chainsaw (unless it’s overflowing, which would not be good). What’s important is that too much oil is not being used by the chainsaw on the bar and chain.
How do I adjust my Stihl oiler?
Insert a small flat-head screwdriver into the oil adjustment screw on the underside of the chainsaw. Turn the screw clockwise to increase oil flow or counterclockwise to decrease the oil flow, reveals Stihl USA.
Why does Stihl chainsaw leak oil?
This condition is deemed to be normal for any chainsaw with a similar bar & chain lubricating system. If the unit continues to seep oil after a few days, the problem may be the vacuum relief valve located in the side of the engine housing between the oil output hole and the bar stud(s).
Why does my Husqvarna chainsaw leak oil when stored?
The oil must be of a viscosity that adheres to the chain without being too thick or too thin. If you’ve chosen the wrong oil for the machine, that may be the reason it’s leaking from the bottom. Husqvarna strenuously warns users to never use waste oil in a chain saw.
How much bar oil should a chainsaw use?
When to Oil Gas chainsaws use about one tank of bar and chain oil for every tank of fuel, so fill the reservoir every time you fill the tank.
Do all electric chainsaws leak oil?
Even after you have removed oil from the reservoir, the electric chain saw might continue to leak oil if the pump is dirty. Excessive oil on the oil pump gaskets can cause leakage. Wipe the gaskets clean and check them for wear. If the gaskets are ruptured, replace them.
Can you use 10w40 in a chainsaw?
You can but it’s not very good for the chain or the environment. The Husqvarna / Stihl stuff is much thicker and vegetable based so it doesn’t fling off the chain as easily or poison your garden! 10w30. Thicker.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
Can I use 2 stroke oil for chainsaw bar oil?
Can You Use 2 Cycle Oil As Bar Oil? You should only use two-cycle oil as the mix, never as a chainsaw bar oil alternative. Using two-cycle oil on the bar will not provide enough tackiness to stick to the chainsaw chain in the summer months. Two-cycle oil also will not work in the winter.
How long does bar chain oil last?
Bar oil itself lasts indefinitely; it’s the containers holding the oil that determines the shelf life. Bar oil will stay in most bottles between 3 and 7 years. The oil base determines the length of time; synthetic oils will last the longest, whereas mineral and plant-based oils have a shorter shelf life.
How much oil does a Stihl chainsaw use?
All Stihl equipment operates on a 2:1 ratio. Use the below as a guide for creating your mixture: 1 gallon of gasoline + 2.6 fluid ounces of oil. 2.5 gallons of gasoline + 6.4 fluid ounces of oil.