Makita 5104 14 Amp 10-1/4-Inch Circular Saw This large cutting capacity sidewinder can reach depths of 3 ¾ inches at 90 degrees, which allows users to easily cut into some timbers.
“The blade raising mechanism on most saws can raise the arbor until the flange almost touches the underside of the throat plate, which is usually about 1/8 inch thick. Generally speaking, a 10 inch saw can cut slightly over 3” deep. Even at maximum bevel, the saw reaches a cut depth of 1-3/4 inches. At Chase Cabinets, owner Bob Chase makes the case is simple: Replacing the 10-inch blade on a table saw with a 7-1/4-inch blade can bring immediate benefits.
One of the most common questions about a circular saw is how deep it can cut. What follows are the most common size of circular saw blades and their normal depth of cut at a 90-degree angle as well as a 45-degree angle. Obviously, a 90-degree cut provides the maximum cut capacity while the 45-degree bevel will limit the thickness you cut through.
A circular saw is a powerful cutting saw, which operates in rotary motion with a spinning blade mounted inside. First, do not set the blade too deep as the circular saw will work more roughly and robustly. To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements.
how deep will a 10 circular saw cut Related Question:
How deep do most circular saws cut?
Circular Saw Sizes Circular saw sizing is based on the blade diameter. Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of about 2 1/2 inches. Compact saws can use anywhere from 3 3/8-inch blades up to 6 1/2-inch blades.
Can a 10 circular saw cut 4×4?
As you can see, it can take a lot of time to cut a 4×4 with a 10” miter saw for two reasons. First of all, the saw lacks the necessary torque for such thick pieces of wood. Secondly, in order to create a relatively smooth, clean, and accurate cut, you have to cut from all four sides.
How deep can a 12 inch circular saw cut?
To sum up, a standard circular saw can offer a cutting depth of 2.5 inches as the maximum, but you can adjust the depth to match your requirements. It’s easy by moving the blade up and down to align against the material before starting to cut.
How thick can a 10 Mitre saw cut?
A saw with a 10-inch blade makes right-angle cuts across a board 5 1/2 inches wide, sufficient for two-by-six lumber. The same 10-inch saw will cut a two-by-four at a 45-degree angle. Manufacturers also make 12-inch versions, which have a maximum cut of about 7 1/2 inches, wide enough for two-by-eights.
What size circular saw will cut a 4X4?
Cutting a 4×4 with a Circular Saw – Guide If you need to cut a 4×4 post, then the ideal tool is a large 12” miter saw. This saw has the blade diameter needed to chop through a 4×4 in a single pass, so if this is an option for you it’s the way to go.
Will a 10-inch miter saw cut a 6X6?
A miter saw with a 10-inch blade installed can cut a 6X6 lumber piece, only it cannot do so with one single pass. This will require a bit more effort as the blade diameter is quite small for the piece of wood you are cutting. To do this cut with a ten-inch blade you’ll need to follow several steps to complete your cut.
How deep can a 6.5 inch circular saw cut?
The 6.5 will cut up to 2 1/16”, while the 7 ¼” cuts up to 2 ⅜”. Minor sure, but it’s when you tilt them into 45 degree angles, that the 7 ¼” can do something the 6.5 can’t. Cut through a 2×4.
How deep can a 6 1 2 inch circular saw cut?
The 18V Brushless Lithium Ion 6-1/2 Inch Deep Cut Circular Saw (C18DBALQ4) is a revolutionary cordless circular saw utilizing a 6-1/2″ blade which allows a 2-19/32″ cutting depth, making it one of the deepest cutting cordless circular saws on the market. This circular saw has a similar cut capacity as a 7-1/4″ saw!
Can a 5.5 inch circular saw cut a 2X4?
Yes! A 5.5 inch circular saw blade is perfect for cutting a 2X4. The blade capacity is deep enough to make a crosscut in 1 stroke. If you want to make a 45 bevel cut then you will need to make 2 strokes.
Will a 4.5 inch circular saw cut a 2X4?
The new WORXSAW Compact Circular Saw is capable of cutting a 2×4 in a single pass. The compact circular saw features a 4-1/2 in. blade that is up to 50 percent lighter than a full-size 7-1/4 in.
Will a circular saw cut a 4×4?
Circular Saw. A circular saw is one of the best means of cutting a 4×4 post. Most people own a circular saw, its portability makes it easy to cut 4x4s from the ground, and they can make precision cuts by using a relatively simple trick.
Can I use a bigger blade on my circular saw?
The answer is generally this is not a great idea. A larger blade will put excess stress on the motor, and may not have enough strength to provide the cutting power at the tooth you need.
How do you rip a 4X4 with a circular saw?
One creative way to rip a 4X4 with a circular saw is to run a pass with your saw down your line on the top side of the 4X4. Then flip it over and run another pass with your saw. Depending on the size of your saw you may need to finish splitting the 4X4 with using a hand saw to cut through the remaining material.
What is the difference between a Sawzall and a reciprocating saw?
sawzall, and what the difference is between the two. They are actually the same thing. The Milwaukee tool company introduced the first reciprocating saw in 1951, and called it the Sawzall. It has since been so widely copied that the terms reciprocating saw and sawzall are now used interchangeably.
Can a 12 miter saw cut a 4×6?
Yes! A 12” miter saw can easily cut a 4 x 6 lumber. A 12 inch miter saw clearly has a bigger blade and has the capability to cut 4×6 lumber in a single pass.
