In common, a standard circular saw, which mounts a 7 1/4-inch blade, can provide a depth of 2 1/2 inch maximum.
Beginners often get confused when it comes to 6.5 vs 7.25 circular saw. It’s not recommended to use either a smaller or larger blade on a circular saw than what the manufacturer recommends to use. A circular saw with a 7.25-inch blade would cut 4×4 materials without any issue.
One of the most common questions about a circular saw is how deep it can cut. What follows are the most common size of circular saw blades and their normal depth of cut at a 90-degree angle as well as a 45-degree angle. Obviously, a 90-degree cut provides the maximum cut capacity while the 45-degree bevel will limit the thickness you cut through.
how deep will a 7.25 circular saw cut Related Question:
How deep can a 7 1/4-inch circular saw cut?
Circular Saw Sizes Standard-size saws use 7 1/4-inch blades and can cut a maximum depth of about 2 1/2 inches.
Will a 7 1 4 circular saw cut a 4×4?
Standard circular saws with 7 ¼” blades can only cut 2 ½” deep, so making the cut in a single pass isn’t possible. That means you’ll need to make multiple passes to cut clean through the 4×4, and this can result in a poor finish unless you take steps to ensure your cuts line up perfectly with each other.
How deep can a 6.5 inch circular saw cut?
The 6.5 will cut up to 2 1/16”, while the 7 ¼” cuts up to 2 ⅜”. Minor sure, but it’s when you tilt them into 45 degree angles, that the 7 ¼” can do something the 6.5 can’t. Cut through a 2×4.
What depth can a circular saw cut?
Since the blade pivots in the middle, you can’t cut to the pivot. As a result, the depth of cuts from other circular saws can be precisely estimated. Moreover, a regular circular saw can have a maximum cutting depth of 2.5 inches, but you can change this by customizing your saw to your needs.
How deep can a 7 inch circular saw cut?
In common, a standard circular saw, which mounts a 7 1/4-inch blade, can provide a depth of 2 1/2 inch maximum.
Will a 7.25 circular saw cut a 4X4?
Like miter saws that measure less than 12 inches, a circular saw’s 6.5-inch or 7.25-inch blade will not cut cleanly through a 4×4. The maximum depth of most circular saws is just 2.5 inches. This means you’ll need to make two cuts.
Can I use a bigger blade on my circular saw?
The answer is generally this is not a great idea. A larger blade will put excess stress on the motor, and may not have enough strength to provide the cutting power at the tooth you need.
How deep can a 6 1 2 inch circular saw cut?
The 18V Brushless Lithium Ion 6-1/2 Inch Deep Cut Circular Saw (C18DBALQ4) is a revolutionary cordless circular saw utilizing a 6-1/2″ blade which allows a 2-19/32″ cutting depth, making it one of the deepest cutting cordless circular saws on the market. This circular saw has a similar cut capacity as a 7-1/4″ saw!
Can you use a 7 blade on a 6.5 circular saw?
NO, a 7″ blade will not fit inside the blade guard. Also, it’s rough on these little saws cutting concrete or tile unless you reduce the blade size.
How deep can a 6 circular saw cut?
Depth. A 6 ½ circular saw can cut materials up to 2.5 inches. It’s perfect for cutting small materials for a small DIY project.
How deep will a 10 inch circular saw cut?
Makita 5104 14 Amp 10-1/4-Inch Circular Saw This large cutting capacity sidewinder can reach depths of 3 ¾ inches at 90 degrees, which allows users to easily cut into some timbers.
Will a 4.5 inch circular saw cut a 2×4?
The new WORXSAW Compact Circular Saw is capable of cutting a 2×4 in a single pass. The compact circular saw features a 4-1/2 in. blade that is up to 50 percent lighter than a full-size 7-1/4 in.
Can a circular saw cut 100mm?
The MAKITA HS0600 240v Circular saw – 270mm blade has the following features: 2000 Watt. No load speed: 4300rpm. Depth of cut: 100mm.
Can you put a 7 inch blade on a 10 inch table saw?
Yes, you can use a 7” blade on a 10” blade table saw. There will be a diminution in the depth of the cut, but it is possible to use a smaller blade. There will be less noise and less waste (sawdust) using the smaller blade, too.
How deep can a 4 1 2 circular saw cut?
The max cutting depth is 1-11/16″ at 90 degrees and 1-1/8″ at 45 degrees.
