On a typical wood or metal cutting blade the hook or of point of the blade should be pointing down for a vertical blade bandsaw, or for a horizontal blade saw the hook of the teeth should be pointed such that they enter the workpiece first as the blade moves. During regular cutting on a well set up bandsaw the blade will move or bow backwards a bit as you press the workpiece into it. The side guides will assist in keeping the blade cutting straight, but they are not an iron lock on the blade forcing it to cut straight.
Being a happy bandsaw owner has a lot to do with your approach to coping with the fact that a bandsaw simply will not cut straight, or, in the sage words of veteran woodworkers, “Adjusting for drift.” Even the top performing 14″ bandsaw on the market, Powermatic’s 14 Bandsaw 1791216K, comes with a no-frills fence with 4 bolts on top rather than easy and obvious thumbscrews or knobs that say, “Adjust me here!”. Making the bandsaw cut nice and straight with this fence is a snap.
If the blade twists and the work piece is harder to push through the cutting area, replace the blade. Loose blade tension can also cause the blade to twist and veer off course when cutting the work piece. Check blade tension by pressing in on the side of the blade using a gloved finger.
This in turn causes the blade to not cut in a straight line. With a dull blade, there is an expectation for it to cut slower and cut crooked. The main thing that normally goes out is the crown, which is what is holding the blade in place, Most of the time the blade is right at the center, but if the crown begins to wear out, it may start allowing more and more movement, causing the blade to not cut in a straight line.
how do i get my bandsaw to cut straight Related Question:
Why won’t my bandsaw cut a straight line?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why does my band saw cut to the left?
The difference between the steak and the bandsaw is where the steak knife is short and thick, the bandsaw blade is generally long and skinny. This becomes a problem because it is possible to push hard enough on the blade to cause it to twist left or right.
Why are my bandsaw cuts wavy?
Re: Band saw Cutting Wavy Cuts. The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.
How do you straighten a bandsaw blade?
How to straighten a bandsaw blade? It is risky but if it’s absolutely necessary, a temporary fix to straighten a bandsaw blade can be done by placing it on an anvil and gently tapping it flat with a nylon head hammer/mallet or using a pair of gas pliers to straighten out the blade.
How tight should my bandsaw blade be?
The blade should deflect no more than 1/4 in. A good place to begin is to tension the blade until the meter reads proper tension for the next wider blade. For example, if you’re tensioning a 3/8-in.
How do I stop my bandsaw blade from wandering?
Draw a pencil line down the edge of the board where you want the cut. Set the guide, and follow the line with your eye. The guide allows you to pivot the board as needed to keep the cut going right down the line – and no fence binding or trouble to worry over.
What causes bandsaw drift?
Drift is cause because the blade buckles under the load. You can see that by stretching a ribbon between 2 points and applying a pressure to one of the edges, it will turn sideway easily. A sharp blade and high blade speed will help a lot with that.
How long does it take to get a WoodMizer sawmill?
And demand is high. “The lead time is 44 to 59 weeks right now for a sawmill,” says Kate Sebring, a sales representative for WoodMizer.
Why does my bandsaw blade stop?
Using a dull blade or the incorrect type of blade can cause the band saw to cut through work pieces slowly. The blade will also move slowly through the work piece if the blade is installed incorrectly. A weak drive motor can also cause the band saw to cut slowly. First, check the installation of the band saw blade.