A catalyst for this seems to be Jim Cummings article “Home Shop Bandsaw” in Fine Woodworking #63. From the hundreds of bandsaw owners I’ve talked with since the article appeared, it seems there are lingering questions on how to adjust a bandsaw blade, the blade choice and operation. “To find the correct tension, you can start with the tension scale on your saw, but you will probably need to fine tune the adjustment. With the saw unplugged, increase the tension on the blade until pushing on the side of the blade with your finger using a moderate amount of force deflects the blade about a 1/4” from its normal position. An interesting experiment is to set the side guys too far from the blade and notice how increased feed pressure and turning make the blade wander.
Even a low-end bandsaw blade tension meter can cost $300. If you use your bandsaw a lot or are doing delicate work, having the proper tension on the blade can be critical and the only way to accomplish this is with a bandsaw blade tension meter. With the bandsaw blade properly installed, and tensioned, and the blade guides properly set, the next issue is to make sure that the bandsaw table is square and level. We suggest that you go through the setup steps in this how to set up a bandsaw properly: the ultimate g guide before starting a new project and each time you change your bandsaw blade.
Install the blade and apply just enough tension to keep the blade securely on the wheels. Instead, tension the blade until your finger is only able to deflect the blade by about 1/4″. This test should be done at the back of the saw where nothing can get in the way of the blade. Adjust the thrust bearings carefully so that they do NOT rotate while the blade moves, but they DO begin to rotate as soon as light pressure is applied to the blade.
Whether you’re a beginner or could just use a refresher, we’re going to walk you through the process for a perfect bandsaw blade adjustment setup every time, no matter what blade you install. Lower the upper blade guide, open the wheel housing(s) and blade guard and carefully remove the blade. So it should be no real shocker that you’ll encounter conflicting schools of thought regarding blade placement on the wheels and how it affects blade “Drift”.
Blades with more teeth per inch will cut more slowly than a blade with fewer teeth, but will make a nicer cut. The material needs to be thicker than three teeth of the band saw blade being used. There are a variety of blades available; see Shop Staff for assistance, or refer to your bandsaw’s manual on how to change the blade.
Most basic adjustments, including setting the blade guide blocks and thrust bearings and adjusting the tension and tracking of the blade, need to be done each time you change the band saw’s blade. Following this schedule of maintenance and tune-ups helps prevent the saw from developing vibrations and blade wander and keeps your band saw cutting straight and true. If your saw blade wanders during cutting and/or you need to turn the tracking control and tilt the upper wheel excessively in order to track the blade, you should check to see if your saw’s wheels are improperly aligned.
how do you adjust band saw Related Question:
Why is my band saw not cutting straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why is my horizontal band saw not cutting straight?
Make sure the blade is running in the correct direction. On machines powered by three phases power so it is common to get the wiring reversed and have the blade running the wrong direction. On all vertical blade bandsaws the working portion of the blade should go down. This forces the workpiece down into the table.
How much tension should a bandsaw blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
When using a horizontal band saw you should adjust the blade guide as close to the work as possible?
The upper guide and guard should be set as close to the work as possible, at least within 1/4 inch. If the band breaks, immediately shut off the power and stand clear until the machine has stopped. Examine blade before installing to see if it is cracked, do not install a cracked blade.
Why are my bandsaw cuts wavy?
The clasic cause for wavy lumber is pushing a dull blade past it’s limits. Sharp don’t get it.