If there is too much fuel mixed with the air, the engine “Runs rich” and either will not run, runs with a lot of smoke, runs poorly or, at the very least, wastes fuel. There is an adjustable plate across the tube called the throttle plate, which controls how much air can flow through the tube. One of these screws controls how much fuel flows into the venturi at full throttle.
how does a chainsaw fuel system work Related Question:
What would cause a chainsaw to not get gas?
If your chain saw isn’t getting gas, the trouble most likely lies in one of those three core components: the fuel tank, the spark plug or the carburetor, or one of the minor parts adjacent to the three.
How does a chainsaw fuel a carburetor?
The carb is operating “normally” at full throttle. In this case, the throttle plate is parallel to the length of the tube, allowing maximum air to flow through the carb. The air flow creates a nice vacuum in the venturi, and this vacuum draws in a metered amount of fuel through the jet.
What does a spark arrestor do on a chainsaw?
The spark arrestor on your chainsaw prevents dangerous hot sparks from igniting fires while you’re working. If the arrestor is clogged or dirty, however, it will also prevent exhaust from leaving the motor, which can prevent it from running.
What do air bleeds on a carburetor do?
Air bleeds, sometimes referred to as “air jets” or “air bleeders” play a vital role in the operation of your carburetor. Air bleeds are responsible for determining the amount of air that will mix with each circuit in the metering block.
Where does fuel go after carburetor?
The mixture of air and fuel flows down into the cylinders. Fuel (orange) is supplied from a mini-fuel tank called the float-feed chamber. As the fuel level falls, a float in the chamber falls and opens a valve at the top. When the valve opens, more fuel flows in to replenish the chamber from the main gas tank.
What part of the carburetor controls fuel entering the carburetor?
The first valve, known as the choke, regulates air flow into the carburetor to mix with the fuel and is only used when the engine is cold. The second valve opens and closes when you depress the gas pedal and regulates how much of the combination exits the carb and goes into the engine.
Can you flood a chainsaw engine?
A flooded chainsaw is caused by too much fuel inside the engine which does not allow the fuel to ignite. Think of it this way, combustion inside an engine needs fuel and air. By having too much fuel, there’s not enough room the for proper air mixture when the spark plug tries to ignite the gas.
How long to wait if chainsaw is flooded?
Let your chainsaw sit for 15-20 minutes to allow the fuel to evaporate from the engine and then repeat the starting instructions.
How do I know if my chainsaw spark plug is bad?
If it’s not producing any sparks at all, your chainsaw needs a new plug. If there are only a few sparks coming out of one side of the electrodes but none on the other side, it’s not bad enough for you to worry about, but it will affect your performance.
Can you run a chainsaw without a spark arrestor?
We can’t run without arrestors here, and the fire danger is so high I wouldn’t anyway. There is less restriction without it, but cleaning them from time to time helps a lot. If it’s hot and dry, I wouldn’t risk it.
Is it OK to remove spark arrestor?
You can safely remove the spark arrestor or even install an aftermarket exhaust system on many ATVs without having to make alterations to your jetting because they are normally set up to run a bit rich from the factory, but this is no general rule!
Do you need spark arrestor screen?
Spark arrestors are needed on all internal combustion equipment, two strokes or four strokes. It is fair to say that two-strokes are more commonly associated with sparks from the tailpipe. That’s because two strokes rev at a much higher rpm and the gas oil mix tends to soot up and gather inside the muffler.
Why does my chainsaw not stay running?
Your chainsaw’s engine needs the right supply of air to run properly. A clogged air filter can be the reason why your chainsaw won’t start or stay running. Find your chainsaw’s air filter and remove it. If it’s clogged or too dirty, wash it or replace it.
How do you check fuel pressure on a carbureted engine?
To test the pump pressure, connect a fuel pressure gauge to the pump line at the carburetor, then run engine 500-1000 RPM. If pressure is not within specifications or varies to any extent at different speeds, repair or replace the pump.