If there is too much fuel mixed with the air, the engine “Runs rich” and either will not run, runs with a lot of smoke, runs poorly or, at the very least, wastes fuel. There is an adjustable plate across the tube called the throttle plate, which controls how much air can flow through the tube. One of these screws controls how much fuel flows into the venturi at full throttle.
how does chainsaw carburetor work Related Question:
Do chainsaw carbs have jets?
They are typically labeled L (low speed jet), H (high speed jet), and I (idler jet). Your saw may be labeled differently (in the photos in the Gallery below, the idler jet is labeled “S”), but you’ll have three screws that correspond to these descriptions.
What are the L and H screws on chainsaw?
The letters on the screws represent High (H), Low (L) and Idle (T). The H screw regulates the Air/Fuel mix during high RPMs, while the L Screw does the same during low RPMs.
Why does my chainsaw only runs on choke?
When your chainsaw only runs if the choke is on the problem, in most cases, is a result of fuel supply problems or a faulty carburetor. To fix the problem you should check and clean the fuel system and carburator.
Why does my Poulan chainsaw dies when I give it gas?
The carburetor might be clogged. A clogged carburetor is often caused by leaving fuel in the chainsaw for a long period of time. Over time, some of the ingredients in the fuel may evaporate, leaving behind a thicker, stickier substance. This sticky fuel can clog up the carburetor and cause the chainsaw engine to stall.
What happens when carburetor fails?
A failing carburetor directly affects your vehicle’s fuel efficiency, so you’ll find yourself spending your hard-earned cash at the gas pump more often. The improper fuel/air mixture can also cause avoidable engine damage.
Can you clean a chainsaw carburetor without taking it apart?
To clean a carb, you have to take it apart. If it needs cleaning, the parts that need cleaning can’t be seen from the outside.
How do you clean a carburetor without removing it?
To clean a motorcycle carburetor without removing it, you’ll need to remove the bowls at the bottom of the carburetor. Once the bowls are removed, spray some carburetor cleaner up inside, wait a few minutes, then spray again to ensure coverage. Then replace the bowls and start the motorcycle to assess how it runs.
Why does my chainsaw dies when I turn it sideways?
Because the fuel covers the jets. When the bar points down or the saw is held sideways the jets no longer have fuel to cover them, it is air. The saw then runs lean and dies.
Should there be gas in the carburetor?
Pouring gasoline into the carburetor is dangerous and should not be done unless there is no other option for starting your car. If your engine backfires during the operation, the gasoline you pour could ignite while it is in your hands.
What part of the carburetor controls fuel entering the carburetor?
The first valve, known as the choke, regulates air flow into the carburetor to mix with the fuel and is only used when the engine is cold. The second valve opens and closes when you depress the gas pedal and regulates how much of the combination exits the carb and goes into the engine.
What are the two hoses on a carburetor?
Registered. The two hoses circled in red are vent/over flow hoses. Should not have any plugs in them. They basically both route between the two carbs, hanging down.
What happens when you run a 2 stroke too rich?
keeping the engine under a light load (you will only be opening the throttle to 1/2 or so) If the needle is set too rich you will hear a sputtering like the choke is on and the acceleration will be slow. If the clip position is too lean the engine will sound quiet and have a “dead” feeling possibly hesitating.
How do I know if my carburetor is too rich or lean?
This method involves looking at the base of the spark plug insulator (white part of the plug) for a slight coloring on the insulator just above where the insulator comes through the steel case. If the mixture is too lean, it will leave no color, while a rich mixture will cause the fuel ring to become more prominent.
What does needle clip position do?
The top needle clip position is the leanest position available. This is because the needle is sitting farther down the inside of the atomizer or emulsion tube, restricting the fuel flow for a longer period of throttle slide travel. The bottom needle clip position is the richest position available.