Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
After reading this post, you’ll know how tight a chainsaw chain should be, how to adjust it, and how to test that you’ve got it perfect. If you’re unable to pull the chain away from the bar, then your chain is too tight. If you keep trying to tension your chain and you just can’t get it right, you may have the wrong sized chain.
There are no formulas or concrete rules on how you should tighten your chainsaw chain. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw. A loose chain will simply flop around the bar grooves, and a chain that is too tight will refuse to budge.
Chainsaw chain tension should be checked and tightened often. A properly stretched chainsaw chain should be a little loose on the guide bar – but not so loose that you can pull the drive links out of the bar nose. Maintaining the proper chain tension is therefore essential because it ensures your chainsaw is safe to use and will last for years to come.
how loose chainsaw blade Related Question:
How Loose Should a chainsaw blade be?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How do I know if my chainsaw chain is too loose?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Why does chainsaw chain keep coming loose?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
How often should you tighten chainsaw chain?
The chain isn’t actually becoming tighter—instead, as you turn the tensioning pin—it pushes the chainsaw bar out a little bit, which takes up the slack on the chain. During a typical afternoon wood-cutting session that lasts 2 to 4 hours, you may need to tighten the chain two or three times.
How much does it cost to tighten a chain on a chainsaw?
It should “give” about a 1/4 inch from the bar without much effort. Finally, while still holding up on the tip of the bar, tighten the bar nuts. Proper chainsaw chain tension is safer, it cuts better and it will extend the life of both your chainsaw and your chain.
When should you throw away a chainsaw chain?
The chainsaw pulls in one direction, which results in a crooked finish. Blunt cutting teeth on one side or uneven teeth lengths usually cause this. The teeth has hit rocks or dirt and broken. If you notice the tops of the teeth are missing you will need to replace the chain.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.
How long does a chainsaw bar last?
Re: how long does a bar last The next, a Granberg, lasted about 2 months. About that time Stihl started using them with the same results. A good bar can be filed a few times on both sides and the tip replaced when needed. They could last almost as long as the saw.
Is it OK to use a chainsaw on wet wood?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
What do you do with an old chainsaw?
Gas and oil can be disposed of at a household hazardous waste collection site for free. Remove non-metal parts and place in the trash. Metal parts can be recycled as scrap metal.