Tightening the screw will tighten the chain, and loosening will loosen the chain. Visit our Chainsaw Chains page to our inventory of available replacement chains and other chainsaw accessories. eReplacementParts.com stocks thousands of parts for many major chainsaw brands, including Echo chainsaw parts.
Important: Always make sure the engine is turned off before you begin tensioning the chainsaw chain. Locate the chain tension adjustment points on your chainsaw. Common locations for adjustment points include the side cover and the front of the chainsaw.
After reading this post, you’ll know how tight a chainsaw chain should be, how to adjust it, and how to test that you’ve got it perfect. If you’re unable to pull the chain away from the bar, then your chain is too tight. If you keep trying to tension your chain and you just can’t get it right, you may have the wrong sized chain.
There are no formulas or concrete rules on how you should tighten your chainsaw chain. Bar oil is going to be consumed at a higher rate, and if the chain is too tight it can also damage the clutch and bearings when you start the chainsaw. A loose chain will simply flop around the bar grooves, and a chain that is too tight will refuse to budge.
how tight should your chainsaw chain be Related Question:
How do I know if my chainsaw chain is tight enough?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it. The chain should snap directly into position.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
How tight is too tight for a chainsaw chain?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Why does my chainsaw chain keep loosening?
Chain Not Set Properly One of the most common reasons why your chain might be coming loose is because it was not set properly. When you go through the steps to tension your chain, you need to finish those steps by setting the tension so it won’t change as you work your saw.
Why is my chainsaw blade smoking?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
How long should a chain on a chainsaw last?
The lifetime of a chainsaw chain has no fixed limit and depends on usage and maintenance. The chain should last many years; 5-6 years should be no problem. However, if the chainsaw chain is used properly and taken care of, it can last way longer.
How often should you sharpen a chainsaw?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Do chainsaw chains stretch?
A chainsaw chain stretches and loosens from tension and extreme friction. The friction from cutting through wood makes the chain very hot and the heat causes it to loosen. The heat expands the guide bar and when it cools, the chain has stretched. The chain will also loosen as it wears down from use.
How do I know if my chain is too loose?
To find out whether your chain is too long take a look at it from the side with your eyes being level with the chain. A loose chain will sag close to or below the chainstays as the chain hangs between the rear cogs and chainring. The chain might skip as you pedal, or even drop off the gears.
Why does my chainsaw jump when cutting?
Improper Chain Tension You can extend the life of your chain, bar and chain saw motor by maintaining the proper amount of tension on the chain. Too much slack in your chain can cause the saw blades to jump the bar. This is commonly referred to as throwing the chain.
Can I use vegetable oil instead of bar oil?
Effective – Vegetable oils have natural properties including good lubricity, resistance to shear, a high flash point, and a high viscosity index. These qualities lend themselves to chain lubricant requirements similar to petroleum-based chain oils, and do not contribute to chain or bar wear over time.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Why is my chainsaw blowing white?
Why is my chainsaw blowing white? While black smoke is caused by the burning of more fuel than air, blue or white smoke is generally caused by the burning of excess oil.
Can you cut a stump with a chainsaw?
A chainsaw, however, can grind up a stump and leave it all but gone; still, you can’t use a chainsaw to completely grind away a stump. After much of the stump is gone, however, dirt and other material can cover the stump so it won’t be noticed.
Is it worth sharpening a chainsaw chain?
Sharpening your chainsaw chain is definitely worth it as a sharp chainsaw chain is easier to work with. It takes less effort to cut through wood and your chain will make cleaner cuts with sharp blades. A chainsaw chain can be sharpened multiple times without much of a cost.