how to adjust a dewalt circular saw Related Question:
How do you change the depth of a Dewalt circular saw?
Determine the blade depth by unplugging the saw and holding it alongside your board with the blade guard retracted. Then loosen the depth-adjusting lever or knob and pivot the saw’s base until the blade extends about 1/4 to 1/2 in. below the board. Tighten the lever or knob and you’re ready to saw.
Why is my circular saw not cutting straight?
What Causes a Circular Saw to Not Cut Straight. A faulty circular saw is likely to have issues such as an unstable blade or a warped blade edge. The problem could also be the way you operate the saw. If you do not operate the circular saw properly, it will not cut straight.
Can you set depth on circular saw?
A circular saw has a depth adjustment lever or knob that releases or loosens to allow for adjustment of the saw’s bottom plate, often called the “shoe.” First unplug your saw, then disengage this lever so that you can freely adjust the cutting depth by raising or lowering the bottom plate.
Why is my circular saw pulling to the right?
If the base plate is not parallel to the blade, the saw will also want to travel to the side. If your saw was dropped at some point the base plate could easily be out of alignment. Turning to the right would indicate that the base is farther from the blade at the front than it is at the back.
Can you make angle cuts with a circular saw?
All circular saws can be adjusted to make angled bevel cuts up to at least 45 degrees. However, when the base plate is tilted all the way over, the lower blade guard has a tendency to catch on the edge of the board.
What is the bevel adjustment on a circular saw?
Circular saws commonly include an adjustment that allows you to set the blade angle anywhere from zero to 45 degrees. Using this feature, you can cut a bevel along the length of a board and a miter across the end.
What is the closest you should put your fingers to the blade while it is running?
Do not put your fingers closer than two inches from the blade. 3. Do not place your hands directly in line with the blade while cutting stock. 4.
Why does my circular saw keep stopping?
Circular saws keep stopping due to a dull or damaged blade usually. However, problems like insufficient battery, or a damaged power cord can also cause a circular saw to keep stopping.
How do you keep a circular saw guard up?
This can be accomplished by rotating the guard into the saw, and holding onto the black handle with the thumb of the right hand (the trigger hand is the left). Pull the guard back before pulling the trigger.
Why do circular saws cut upwards?
The saw’s motor runs the blade rotation in a way that the circular saw teeth direction points up as it enters the wood you’re cutting. It’s intentional to create the most stable, accurate, and safe cutting. As the blade teeth hit the material, they rip from the bottom through the top.
Why are my circular saw cuts curves?
Check whether the blade is parallel with the edge of the base, the edge that goes against the guide. If the blade is further away at the front, it’s going to want to walk away from the straight-edge. This is probably easiest to do when the base is in the 90 degree position rather than set at a bevel.
Why does my circular saw blade stop spinning?
The most common reason your circular saw blade stops spinning is because your workpiece is pinching the blade. This can also cause the blade to kickback. To prevent this from happening you need to support your workpiece properly to allow it to set securely through the entire cut.
Which side of the line do you cut with a circular saw?
When appearance matters, make cuts with the good side facing down, as circular saws can splinter the wood on the top side. Making your cut line on masking tape can reduce splintering. Start over if you see that you’ve veered off from the cut line instead of trying to curve your way back on track.
Which cut is when you cut a straight 90 degree across the grain?
A crosscut is a straight, 90-degree cut that cuts across the grain of the wood. Usually, that means turning long boards into shorter ones. On a table saw, you will usually use a miter gauge to make crosscuts. It’s the most basic cut you can make.
