Justabout anyone who has used a chainsaw has been there: One moment you’re happily cutting a log, spitting out a nice plume of wood chips, when suddenly, everything comes to a sudden stop. A log supported on one end should, in theory, be no problem, since the kerf opens away from the chainsaw bar as you cut downward. Sometimes I have to sacrifice a wedge and cut it with the chainsaw.
Learning how to prevent your chainsaw from pinching when you’re cutting firewood is something everyone should understand. There are two easy techniques I like to use to prevent a chainsaw from pinching when the tree or tree top is already on the ground and you’re ready to cut it up into firewood sized pieces. Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
how to avoid chainsaw binding Related Question:
Why does my chainsaw keep jamming?
Here are our explanations! Indeed, whether it is a chainsaw electric ou thermal, it is the teeth of its links that come into direct contact with the wood and the materials to be cut. As a result, dirt, wear on the guide or links and even the motor can be the cause of jamming.
Why does my chain saw bind?
Re: New chainsaw binding during cutting If you’re only sawing something that size occasionally, it can be done. It’s probably bogging down because it just doesn’t have the power for the job. If you hold it back to keep it from bogging you’ll probably be able to get through it.
How do you cut down a tree without a pinching chainsaw?
Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Should a chainsaw chain move freely?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it.
Why does my chainsaw bar keep bending?
A saw that has had one side of the chain nicked on a rock or dulled in the dirt will cut in a circle. A chain that has been sharpened differently on one side of the chain than the other will cut in a circle. A bent bar might cut crooked or straight, but, it will get hung up in the kerf.
What is bucking a tree?
Bucking a tree The process of cutting a tree into usable lengths is called bucking. Bucking often occurs as a tree is being limbed, such as when the limbs of the crown are to be used as firewood. When cutting firewood, make sure you know the needed length of wood before you leave home.
Can electric chainsaw cut trees?
Although electric chainsaws are smaller and easier to carry, most lack the power and stamina to cut down large trees. If you have big trees on your property that you want to remove or cut into firewood, a gas model is your best bet. Electric chainsaws come in two types: corded and battery-powered.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
How much tension should be on a chainsaw chain?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
How do you know if your chainsaw clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
Can a bent chainsaw bar be straightened?
Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .
Why does a chainsaw cut crooked?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
Why does my chainsaw bar get so hot?
If your chainsaw’s blade is overheating and producing smoke, it means that there is a serious problem with it. In that case, you must start troubleshooting at once. The two most common causes of the overheating or smoking of your blade are lack of lubrication of the bar guide or the engine and lack of air.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.