To do the job safely, you should learn how to cut a fallen tree with a chainsaw. Limbing a tree would be easier if you can cut through all the branches the tree has. To cut the fallen branches, cut through both sides in two independent shots.
Whether you are using a chain saw to cut firewood, trim trees or harvest large timber, you will be performing three basic operations: felling, limbing and bucking. Experienced loggers are often killed by felled trees that hang up or snag in adjacent trees. Proper limbing techniques to reduce damage to the tree are covered in MU Extension publications G5160, Pruning Forest Trees, and G6866, Pruning and Care of Shade Trees.
how to chainsaw a fallen tree Related Question:
How do you cut a fallen tree without getting saw stuck?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How do you cut a log under pressure?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
Do I cut compression or tension first?
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
How do you cut a fallen tree with an AXE?
Chopping With An Axe: If you’re using an axe, then start with a 45 degree angle chop (to create a notch) on the side that you plan for the tree to call. Continue to chop in 45 degree angle chops, with each chop opposite each other. Continue this until you’re about a third of the way through the tree.
What is chainsaw bucking?
The process of cutting a tree into usable lengths is called bucking. Bucking often occurs as a tree is being limbed, such as when the limbs of the crown are to be used as firewood.
What are the 3 main ways to cut a log?
The most common methods are plain sawing, quarter sawing, and rift sawing.
How do you cut a chainsaw?
Teeth are arranged in alternating right/left fashion to help a chain cut evenly and straight. Depending on the length of the chain for a certain size bar, there will either be an equal number of alternating left hand and right hand cutters, or the chain will end with 2 back to back same-side cutters.
Which way will a tree fall when cut?
Plan the Notch The notch is what will allow the tree to fall properly, so you want it on the “fall side” so the tree will fall in the direction of the notch. The fall side should be the heaviest side of the tree. Cut at a comfortable working height.
Is it OK to cut branches off trees?
Yes, you can kill a tree by over pruning it. It’s best to start small, and only remove a few branches at a time. Then every year, continue working on it until you reach the desired shape. Also, don’t cut off any large limbs unless they are dead or severely damaged.
What tool is used to direct the fall of a tree?
The felling wedge provides greater felling force than the different types of breaking bar. In extreme cases, you can use a rope and winch, which is the safest and most powerful way to fell a tree. FOOT BREAKING BAR: The foot breaking bar is suitable for small trees when thinning.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
Can a chainsaw cut through dirt?
Don’t Cut Into Dirt All it takes is a second in the dirt to dull the cutters. In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch. Plus, dirt wears the sprocket at the bar tip.
What is the fastest way to remove a tree stump?
The fastest way to remove a tree stump without using a grinder is the chemical method. By applying chemicals to holes drilled into the stump, you speed up the natural decay process and the remaining tree fibers and roots will break down more quickly.
Can you chainsaw upwards?
Never cut above shoulder height. Work on the uphill side of trees so they’ll roll away from you instead of over you.