It’s often best to use the undercutting chainsaw technique to reduce the chances of the chainsaw getting pinched or stuck during a cut. A word of caution when using the cross cutting chainsaw method: the chainsaw will try to push back at you. By using these proper chainsaw cutting techniques, you should be able to take care of most common tree cutting jobs.
Like big ones that you can’t cut 3/4 of the way then rotate the log. Cut the bottom a bit first in areas that it made sense. Cut the logs into manageable sections to roll and finish cuts without hitting the ground.
If the trunk is on a fairly firm surface, you can cut the trunk to length where it is. Making thin trunks, branches and split pieces into firewood. Once you have cut your own logs, they will need to dry for around two years before they can be used on the fire.
First cut should cut should be made from the underside towards the top about 1/3 of the way through the log. Once you had assessed the situation, begin to cut the limbs supporting the tree, cut from under these limbs to avoid the chainsaw getting pinched or stuck. Make an initial cut upwards, about 1/3 of the way through the branch, a short distance from the trunk of the tree so you have room for the final cut which will be close to the trunk.
how to chainsaw logs on ground Related Question:
How do you saw a log on the ground?
Cutting a Log on the Ground Technique Start cutting from the top of the log, applying light pressure to the chainsaw. The chainsaw should do the work, and the teeth should pull the chain bar into the wood. Don’t let the guide bar nose or chain touch the ground or other objects.
Can you chainsaw into the ground?
Don’t Cut Into Dirt In addition to dulling the cutters, dirt also wears out the chain links faster, causing the chain to stretch. Plus, dirt wears the sprocket at the bar tip.
Can you dig a trench with a chainsaw?
Yes! Chainsaws are great for digging trenches but there are some downsides so make sure you weigh all of your options before deciding what method will work best for this project.
Can you cut wet logs with a chainsaw?
Can you cut wet wood with a chainsaw? Yes, you can cut the wet wood with a chainsaw. Besides, there is a misconception that wet wood can impact the chainsaw bar and chain. But actually, the damp wood will not dull the chainsaw any faster than using it on other types of wood.
Can you use a chainsaw to cut dry wood?
Wet Wood Vs Dry Wood It may come as an eye-opener to some. But wet wood is actually much easier to cut than dry wood. With dry wood lacking moisture content, more friction is created as the chainsaw chain comes into contact with the wood fibers. This friction results in the chain slowing down.
Can I use chainsaw on tree roots?
Once you’ve sliced the stump almost all the way to the ground, continue cutting it — and the soil — diagonally and at different angles. Don’t go more than a foot into the soil. Chainsaws are powerful machines, and you don’t have to worry about dirt damaging it or knocking the chain off.
Can I use chainsaw on roots?
Chainsaws are strong equipment that dirt won’t damage or lose its chain. Keep in mind that some timber might be left beneath the earth. Large roots can also be taken out by cutting vertically into the ground and then pulling out with a shovel or pickaxe.
What happens if you run a chainsaw without bar oil?
Without lubricant, the speed at which the chain moves over the chainsaw bar can cause some serious friction. A slowed-down chain and excessive fuel burning mean there’s a lot of friction between your bar and chain, which means a lot of heat is being produced that could do major damage to your saw.
How do I stop my pinching chainsaw log?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How do you get rid of fallen tree root balls?
Try to cut far from the root ball. Next, use the grub hoe to lift out the cut roots. Pull additional ones out by hand if you can. Push the stump back and forth to loosen the roots and continue to cut and pull roots until you are able to remove the root ball from the soil.
What is the most common chainsaw injury?
The most common hazards associated with chainsaws are injuries caused by kickback, pushback, and pull-in. Kickback is the most common and poses the greatest hazard. Kickback occurs when the rotating chain is stopped suddenly by contact with a more solid area throwing the saw rapidly backward toward the operator.
How do you cut wooden logs?
Cut the log into sections approximately 30cm long, or so they’ll fit in your firebox. For thicker logs, you can cut them along the middle to split them into 2 halves. Place your freshly cut firewood in a dry location and allow it to dry properly. This may take up to two years.
What should you not do with a chainsaw?
Don’t Cut on the Ground When Using a Chainsaw Cutting on or near the ground puts you at risk for sinking the bar into the dirt. When learning how to use a chainsaw safely, one of the first things you should do is make sure to make your cuts off the ground.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
Why does my chainsaw dull so fast?
Dirt Causes A Chainsaw To Dull If you’re cutting through logs and your angle of approach is too steep, a simple cut through could nick dirt or even worse, rocks on the floor causing your chainsaw to jerk, thus dulling.