To make the proper cuts; you’ll need to install the correct blade, which means you’ll need to know not only how to change the band saw blade, but also how to adjust the saw to keep the blade that you do install tracking straight and true. In the following step-by-step tutorial, learn how to change your band saw blade as well as how to make the adjustments necessary to keep your band saw blade cutting properly. Before you can begin to truly tension and adjust the tracking on your new band saw blade, you’ll need to loosen the band saw guide blocks and rollers that keep the blade tracking properly.
Speaker: Today, I’m going to walk you through the process of changing a band saw blade. It’s pretty simple, but there are three main things to consider: blade tracking, blade tension, and guide adjustment. Since the blade is a continuous loop, the table is slotted so that you can get the blade out.
The rear blade guard wraps the bandsaw blade while protecting you in the event of blade rupture. All most all bandsaw problems are blade related and a dull blade can cause blade drift. Knowing how to change a bandsaw blade can easily help you get rid of these problems quickly.
Installing the blade is almost identical to taking it off, but this time you WILL need to re-adjust the upper and lower blade guides and the Thrust Bearing. So install the new blade by placing it on the upper wheel first, then the lower wheel, and now is a good time to take up a bit of slack in the blade. Before you start to align the blade on the wheel, make sure none of guides or thrust bearings are touching the blade … now, spin the upper wheel while adjusting the angle of the blade.
I presume you have chosen a new blade or just received a freshly sharpened band from the saw doctor! It is time now to fit your bandsaw blade. Loosely position top guides onto the band saw blade. I have made a video on how to change your bandsaw blade and setting up your guides.
how to change a bandsaw blade Related Question:
How often should you change a bandsaw blade?
On average your bandsaw blade should last 6 months to as long as a few years depending on what your cutting with it. Make sure to match your blade strength and quality to the project and material your cutting.
What do you do with old bandsaw blades?
There is life for those old, broken, and dull bandsaw blades. Just cut the old blade into sections about 12″ long. Stack the pieces together, alternating the teeth so that they don’t touch their neighbors. Use either same tape, or just braze the ends together,.
Can I put a wider blade on my bandsaw?
An 18-inch diameter wheel can use a 0.032-inch thick blade that is 3/4 inch wide. In general, thicker and wider blades will be the choice when sawing dense wood and woods with hard knots. Such wood needs the extra strength of a thicker, wide blade to avoid breaking. Thicker blades also deflect less when resawing.
Are bandsaw blades worth sharpening?
Since a carbide-tipped bandsaw blade will cost well over $100, spending a third of the cost of the blade (or more) to get it sharp and working like new again can make financial sense. However the majority of bandsaw blades, the Wood Slicer included, are not worth spending money to have sharpened.
How much tension should a bandsaw blade have?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
Why won’t my bandsaw cut straight?
Band Saw: Why won’t my band saw cut straight? When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
Why do bandsaw blades break?
Machine Defects Even the best blades can fail if there is something else wrong with your bandsaw, and even a small misalignment of bearings or guides can put a twist in the blade as it goes around. Resulting in tension being applied in all the wrong ways which will lead to early breakage.
Why does my bandsaw blade wobble?
The blade on a saw left idle for long periods of time can leave an impression in the rubber tire which might cause erratic tracking. Purchase and install aftermarket replacement tires. (Search for “bandsaw tire” at woodcraft.com.) If you still see a back-and-forth motion, the culprit is probably the wheel itself.
How long is a shopsmith bandsaw blade?
The Shopsmith Bandsaw accepts continuous- loop blades 72″ long and 1/16″-5/8″ wide. Shopsmith offers a variety of blades from 1/ 16″ wide to 5/8″ wide for cutting wood, plas- tics and nonferrous metals. To use a 1/16″ blade with the Bandsaw, you must install and use Cool Blocks (Part No.
What does TPI mean on a bandsaw blade?
You must select the correct Teeth Per Inch (TPI) for the thickness of material you are cutting.
Is more TPI better?
Woodworkers quickly learn that the number of teeth-per-inch (TPI) on the blade has a big impact on the quality of a cut. The general rule of thumb is “the more TPI, the smoother the cut.” The true answer, however, is just a little more complicated than that, as you’ll learn once you understand how saw teeth work.
Are band saw blades interchangeable?
For cutoff work, band saw blades should be as thick as the saw and material will allow. TPI stands for “teeth per inch” when talking about band saw blades. “Pitch” is interchangeable with TPI when talking about band saw blades.
How many times can a bandsaw blade be sharpened?
It often makes sense to replace a dull blade with a new one, but you can sometimes get the best value out of merely sharpening an old blade instead of replacing it altogether. You should typically be able to get two to three sharpenings before you need to change your blade completely.