You can change a band saw blade and tension it properly in a couple of minutes. Turn on the band saw and position the pencil line parallel to the blade at the point where the blade should enter the wood. Install a thin, fine-tooth blade that is at least 1/2 inch wide into the band saw.
Width: Wider blades are best for thicker wood and straight cuts because they ‘wander’ less than narrow blades. The square steel guide blocks found on many older saws are bad news: They can cause a blade to overheat, and they’ll quickly dull a blade if they come into contact with its teeth. Cut tighter curves, reduce blade vibration and increase blade life by truing the blade with a saw blade finishing stone.
The narrower the blade, the tighter the spots you can cut; in fact, some band saw blades rival a scroll saw for cutting tight curves. I’m only cutting the side of the pattern with the tightly curved cuts – the other side is a gentle curve we can easily cut later, so leave that portion intact for now to facilitate handling. With the earlier waste pieces removed, it’s easy to cut several relief cuts to allow the blade to finish the curve.
Here’s a tip on how to cut curves on the bandsaw. A few extra cuts on the bandsaw can almost eliminate this problem. As you make the cut on the shape itself, the falloff will do just that – in small, manageable pieces and without binding the blade.
If your bandsaw is close to the lower range, you’ll get a good cut. The general guidelines for bandsaw use to achieve a straight and true cut are not really different from those applicable to other power saws – – table, jig, chop, skill. Sharp blades, proper tension and speed, using a fence for that straight cut and letting the blade do the work will give you what you want, whether it’s simply ripping a thick slab down or making that fancy curve cut on table legs.
how to cut with bandsaw Related Question:
How thick can a band saw cut?
Band saws are the undisputed champ when it comes to cutting curves and slicing through thick material. Many small band saws can slice though lumber a full four inches thick, and bigger saws handle six-inch cuts.
What materials can a bandsaw cut?
Most bandsaws have two wheels rotating in the same plane, one of which is powered. The blade itself can come in a variety of sizes and tooth pitch (teeth per inch, or TPI) which enables the machine to be highly versatile and able to cut a wide variety of materials including wood, metal and plastic.
What can I use a band saw for?
A band saw can be used to cut curves, even in thick lumber, such as in creating cabriole legs, to rip lumber and to crosscut short pieces. The most common use for the band saw, however, is in cutting irregular shapes. The second most common use is in resawing or ripping lumber into thinner slabs.
What is the difference between a table saw and a band saw?
Instead of the solid, circular plate of steel with carbide teeth on a table saw, the blade of the band saw is exactly that—a narrow, flexible band of steel with teeth formed along one edge. The band saw blade is stretched and driven between two or three wheels.
How much tension should a bandsaw blade be?
For carbon steel toothed blades (cutting blades) this is typically 15,000 to 25,000 PSI. Slitting type blades typically are tensioned in the range of 12,000 to 20,000 PSI. In general bandsaw blades are never tensioned past 35,000 psi.
Why does my bandsaw cut crooked?
When the band saw cuts crooked, a dull blade, improper feeding, loose blade tension or not using a work piece guide could be the cause. Use the rip fence or miter gauge to guide the work piece uniformly through the cutting blade to make straight cuts.
How thick can a 9 inch bandsaw cut?
There are several $99, 9 inch band saws on the market in my area (Ryobi, Skill). The are able to cut a thickness of 2 ½ inches.
How many teeth does a bandsaw blade have?
The general rule of thumb is: For wood and soft materials aim for 3 – 6 teeth in the workpiece. For metals and harder materials aim for 6 – 24 teeth in the workpiece.
How much HP does a bandsaw need?
A 3/4 or 1 HP bandsaw is pefectly adequate for re-sawing stock at home….
Which is better scroll saw or bandsaw?
The band saw blades are thicker and more reliable than a scroll saw blade. This makes them faster at cutting but makes the cut a bit more coarse. You can’t make super tight turns, like with a scroll saw, but you can use thick wood, which a scroll saw won’t accommodate.
Can a band saw cut stainless steel?
Bi-metal band saw blades cover the broadest range of sawing applications. 95% of companies and individuals cutting the following materials should use a bi-metal band saw blade: carbon steel, tool steel, structural steel, stainless steel, pipes/tubing, die steel, angles, flat stock and mixed metal applications.