I don’t know if bar/chain oil can break down like gas and cause damage…or if it is ok to leave in the saw. Biological oils will turn to resin if left for too long, but the ordinary run of the mill bar lube can be left in. You can see why you dont want the old gas mix in your carb when you try and fire up the saw after 6 months, but the oil should still be OK. Ian.
My neighbors Stihl 020T is not getting oil to the chain. The manual says to flush the oil tank, but I am not sure what to flush it with. When I drained the oil, a bunch of crap came out with the oil, so I probably should clean out the tank before reassembling.
Your STIHL chain saw likes dry, dustfree conditions. Your chain saw should always be packed away in a dust-free environment. Always store your chain saw out of reach of other people.
how to drain chainsaw oil Related Question:
Should you drain oil from chainsaw?
It’s important to note that oil tanks cannot simply vent into the atmosphere, as this could lead to the oil leaking onto the operator during use. To avoid your chainsaw from leaking oil whist in storage, the best solution is to drain the chainsaw of its bar oil and fuel mix and store the chainsaw empty.
How do you drain oil and gas from a chainsaw?
Move to a well-ventilated area and unscrew the lid of the gas tank on the chainsaw. Situate your plastic gas can within reach and remove its lid as well. Place the straight portion of your hand siphon into the chainsaw’s gas tank. Insert the drainage hose of the siphon into the gas can.
Can you leave chain oil in a chainsaw?
Biological oils will turn to resin if left for too long, but the ordinary run of the mill bar lube can be left in.
Is chainsaw oil the same as motor oil?
Bar and chain oil is stickier than regular motor oil, so it stays on the chain longer. Motor oil flings off the chain more quickly, so if you try Terry’s tip, be prepared to refill the oil on your chain saw more quickly than with regular bar and chain oil.
Can I use 10w30 for chainsaw bar oil?
As a matter of fact, you can actually use regular 10w30 motor oil on a chainsaw as one of the alternatives in case you don’t have bar and chain oil. That’s because 10w30 oil has enough thickness and viscosity that will allow it to withstand the friction that is happening whenever you are using a chainsaw.
What happens when you put straight gas in a chainsaw?
If straight gas is used, it can damage and ruin the piston and crankcase within a minute, as the gas doesn’t take long to burn out these sensitive parts. Drain the tank immediately into a separate fuel container.
How do you drain the gas out of a Stihl chainsaw?
You need to drain your tank of your gas with ethanol then pour in some Stihl Motomix and let your machine run for a few minutes to get the bad fuel out and the motomix in. Once you do this, you can drain your tank and put your equipment up for the year.
What happens if you run straight gas in a 2 stroke?
Without lubrication, it’ll cause high friction, causing heat and causing metal filings from the piston rings knocking around, and losing a seal. In a way, oil counteracts all of these. If it’ll still turn over, flush the fuel, and put in the correct mixture of petrol and oil.
What happens if chainsaw runs out of bar oil?
Increased Bar & Chain Wear No bar oil equals increased friction and heat. That adds up to a huge increase in chain and bar wear. Without bar oil, the chain teeth, drivers and links will all wear far more quickly. The increased friction can cause teeth to break.
Should you run a chainsaw at full throttle?
Engine Protection Generally, two-stroke chainsaw engines are built to conveniently run at full throttle without an engine breakdown. Therefore, running at any throttle speed below the full throttle is not advised.
Why does my chainsaw leak bar oil when stored?
When a chainsaw is in use most of the oil is absorbed by the log and sawdust produced by the chain, therefore leaving little to drip to the surface under the saw.
What weight is chainsaw bar oil?
What viscosity is chainsaw bar oil? The viscosity of chainsaw bar oil can vary depending on the formula but 30W is standard. In cold weather, a thin 10W chainsaw oil may be advantageous, while very hot temperatures may require a much thicker 40W or 50W formula.
How often should I oil my chainsaw?
It is recommended that you grease the bearing in the tip of the bar each time you refuel. Make sure to grease the tip at the end of the day as well to help prevent moisture from entering the bearing as the bar cools.
Can I use 2 stroke oil for chainsaw?
No, you can’t use any 2-stroke oil in your chainsaw. Some 2-stroke oils are built for motor oils, and this might damage your chainsaw. Also, 2-stroke oils for an air-cooled engine are different from a water-cooled engine.
Can any oil be used for chainsaw bar oil?
Generally, chainsaws can handle a wide range of lubricants. Vegetable and canola oils work well, and automobile motor oil will too, as long as you observe the SAE ratings and use the appropriate oil weight for the season. Always use fresh, never used, oils.