The problem is that the chain is so much harder then the bar rails. My advice would be square it up the best you can then use it for stumps and go get yourself a new bar for all your other cutting, its always good to have a stumping bar. If youre gonna try to hand file those rails, clamp your file in a vice and draw the bar across it while pressing down flat against the vice jaws to maintain squareness.
If the bar you are using has significant heel wear, your saw probably has a tendency to “Throw” its chain. If you compare a worn bar to a new bar, you will notice the warn bar has a much narrower heel. To inspect a guide bar for damage, first remove it from the saw.
Learning how to sharpen a chainsaw may seem like a daunting task the first time. The chainsaw blade can be left on the saw, and the chainsaw bar can be clamped in a vise to hold it in place. Because there are so many different chainsaw blade variables, you need to know your chainsaw blade exactly. The chainsaw tooth diameter and cutting angle are the two main factors we will need to know to sharpen the blade. Increased vision allows for easy assessment of each cutting tooth as you sharpen your chainsaw blade. If there is any slack in the chainsaw blade, tighten the chain before you begin to sharpen. Timberline Chainsaw Sharpener 5/32″Timberline Chainsaw Sharpener 3/16″Timberline Chainsaw Sharpener 7/32″. Oregon makes an electric bench chainsaw blade sharpener that can be adjusted to sharpen nearly any type of chainsaw blade.
how to file chainsaw bar Related Question:
What are the holes in a chainsaw bar for?
These two holes are used to hold the saw blade. if your chainsaw blade not have holes or just have one hole. it not work. if you know how to drill, you can drill two holes on your chainsaw blade.
How do I know what size file for my chainsaw chain?
Simply put, the type of chainsaw file you need directly corresponds with the size of your chain pitch. The larger the pitch will mean the higher the cutting teeth will be. The higher the teeth will therefore mean the larger the file will need to be.
Can you drill a chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
How often should you flip the bar on a chainsaw?
Some professional loggers would advocate that you should flip your chainsaw bar at the end of every use, particularly when you are cleaning up. Others suggest a more relaxed approach advising that you flip the chainsaw bar only when you are changing your chainsaw blade.
How often should you change the bar on a chainsaw?
If you are looking for a general idea for how often you should replace a chainsaw bar, a rule of thumb is to replace the bar of your chainsaw once after you have gone through three chains on the same bar.
Should a chainsaw bar get hot?
It is normal for the blade of your chainsaw to produce some heat. But it should not overheat or smoke. If you notice any overheating or smoke coming out of the blade, you should stop its use at once.
What chainsaw chain do professionals use?
Typically only professionals and experienced chainsaw users use full chisel chainsaw chains. They are typically used to cut through hardwood such as oak as their square-cornered cutting teeth are more geared up to power through the wood.
Why does my chainsaw blade go dull so fast?
Is the wood that you’re cutting with the chainsaw particularly dirty? Many chainsaw enthusiasts have noted that their blades dull faster when they’re cutting muddy wood. If the logs that you’re cutting up are muddy, then perhaps that is the sole reason why your blade is dulling too fast.
What size file do you use on a 3/8 chainsaw chain?
With that said, the Stihl 3/8″ chain is identical in size to Oregon and other brands which all recommend a 7/32″ file.
Does skip tooth chain cut faster?
A skip chain has fewer cutting teeth than a conventional chain which means it won’t be dragging as many teeth through the wood you’re cutting. Less drag on the chain means less power is needed to cut through the log. That means the motor on your saw runs faster which keeps it in a more efficient power curve.
How long should a chainsaw blade stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
Why does my chainsaw cut sideways?
Uneven top plates can cause a chain to cut crooked. It’s important to keep all top plates equal length. Dull cutters damaged by rocks can cause a chain to cut crooked. It’s important to remove all damage from cutters prior to cutting.
How do I know if my Stihl clutch is bad?
Does the engine loose revs, or the engine keep revving and just the chain stops? If the engine is still running at normal revs, and the chain slows down, then it’s a problem with the clutch. Worn out, gummed up, jammed springs etc. If the engine looses revs under load then it’s more likely a fuel or carb problem.
Can a bent chainsaw bar be straightened?
Solid body bars with replaceable noses can be straightened by hammering with the bend peak up on a flat anvil. Laminated bars need a piece of rubberized belting of approximate 1/4″ thickness between bar and anvil to properly hammer straighten .
Why does my chainsaw bar keep bending?
A saw that has had one side of the chain nicked on a rock or dulled in the dirt will cut in a circle. A chain that has been sharpened differently on one side of the chain than the other will cut in a circle. A bent bar might cut crooked or straight, but, it will get hung up in the kerf.