Getting your chainsaw stuck in a tree can and will happen to most people who use a chainsaw from time to time. When the tree is on the ground, you will have better luck with different tools, and you don’t necessarily have the downward pressure of the entire tree on your chainsaw. Strategic use of wedges can ensure that the tree doesn’t fall back on your chainsaw so you can cut all the way through, and this also ensures the tree falls in the direction you want it to.
Misjudging where the tension is can cause the chainsaw to become trapped. It is never a good idea to shake your chainsaw while the engine is still running. To do so could cause irreparable damage to your chainsaw and potentially fatal injury to yourself or others.
Retired Conventional hand-felling logging operation with cable skidder and forwarder, Frick 01 handset sawmill. If possible, get into a couple of the courses of the Game of Logging and,. I’ve used a car jack to lift the log and get the saw out works on big logs too.
how to get chainsaw unstuck Related Question:
How do you get a chainsaw chain unstuck from a tree?
The best way to free a trapped chainsaw is to use a felling wedge or a crowbar to gently lift the pressure and tension of the tree off of your chain and bar. Before attempting to do this the engine should be turned off to prevent the chain from accidentally moving and causing damage or injury.
How do you loosen a chainsaw?
A properly-tensioned chainsaw chain should still be just a little loose on the chainsaw guide bar, but the chain needs to be tight enough that you can’t pull the drive links out of the bar nose.
Can you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
Why does my chainsaw not turn?
The chain tension may be too tight. Easy fix, just loosen the bar-retaining nuts and rotate the tensioning screw counterclockwise to the correct tension. Then tighten the nuts back up.
Why do chainsaws get stuck?
Well, blades can easily get stuck when you’re cutting downwards and the log or tree is not perfectly level with the ground. If a log is not sitting firmly on the ground when you cut, the downward force can cause the log to close up on your chain.
How much tension should be on a chainsaw chain?
It should “give” about a 1/4 inch from the bar without much effort. Finally, while still holding up on the tip of the bar, tighten the bar nuts. Proper chainsaw chain tension is safer, it cuts better and it will extend the life of both your chainsaw and your chain.
What causes a chainsaw bar to bend?
A saw that has had one side of the chain nicked on a rock or dulled in the dirt will cut in a circle. A chain that has been sharpened differently on one side of the chain than the other will cut in a circle. A bent bar might cut crooked or straight, but, it will get hung up in the kerf.
Should a chainsaw chain move freely?
The chainsaw chain should feel snug but still pull freely. Finally, perform a “snap” test to ensure proper saw chain tension. Simply pull the chain on the underside of the guide bar down so one or two drive links are out of the guide bar rails and release it.
How do you cut down a fallen tree under tension?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
How long do chainsaws stay sharp?
A chainsaw may only need to be sharpened once a year if it is rarely used, but a tool that is frequently used will need to be sharpened regularly to ensure that the blade doesn’t get too dull. On average, a chainsaw blade will retain its sharpness for about 3 hours of actively cutting through wood.
How does oil get to the chain on a chainsaw?
As you throttle up, a worm drive engages the pump to send oil through a port that releases onto the bar. As the chain moves across the bar, it distributes the oil across the surface, reducing the friction and the heat that occurs when cutting.
Which way should chainsaw teeth face?
The direction of the chainsaw blade is always the same regardless of the type or model of chainsaw. So the sharp edges of the blade should always face the clockwise direction. If you check from the top, you will notice that the sharp edges are facing the direction opposite the chainsaw body or motor.