Justabout anyone who has used a chainsaw has been there: One moment you’re happily cutting a log, spitting out a nice plume of wood chips, when suddenly, everything comes to a sudden stop. A log supported on one end should, in theory, be no problem, since the kerf opens away from the chainsaw bar as you cut downward. Sometimes I have to sacrifice a wedge and cut it with the chainsaw.
Learning how to prevent your chainsaw from pinching when you’re cutting firewood is something everyone should understand. There are two easy techniques I like to use to prevent a chainsaw from pinching when the tree or tree top is already on the ground and you’re ready to cut it up into firewood sized pieces. Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
A bigger cc saw would be better for a full bar going straight down the cut, with a smaller saw like you have you can lessen the load on the engine and keep the engine and chain speed up by slowly see-sawing the bar up an down a bit this will reduce the amount of wood the saw is cutting at one time and still cut the whole log off. Since you already have the 31 cc saw, as someone else mentioned, keep it and look at 50 cc or larger saws as your main saw, cut with your main saw , use the small one to cut yourself out of a pinch if you get hung. A good 50cc saw is hard to beat for firewood, if you need bigger then hire one when you have enough of the big stuff laying about, its better than buying a big one and being stuck with it for the 80% of the time your cutting normal sized wood, they get heavy, and some drink a lot of fuel too.
how to keep chainsaw from binding Related Question:
Why does my chain saw bind?
Re: New chainsaw binding during cutting If you’re only sawing something that size occasionally, it can be done. It’s probably bogging down because it just doesn’t have the power for the job. If you hold it back to keep it from bogging you’ll probably be able to get through it.
Why does my chainsaw blade keep tightening?
Re: Chain tightens by itself Has the oiler stopped working, or the oil feed hole in the bar got plugged with sawdust. Running without oil will do that sort of thing.
Why does my electric chainsaw keep stopping?
If your electric or gas saw’s chain won’t turn around the bar, chances are that the chain brake is stuck. On some saws, resetting the chain brake is as simple as pushing in on the side cover of the saw’s body with one hand, and pushing the chain brake forward while grabbing the top handle with the other.
Why does my chainsaw chain keep spinning?
Carburetor Idle Adjustment The most probable – and easiest to fix – cause of chain rotation while the chainsaw engine idles is a poorly adjusted idle setting on the carburetor. The result is that too much fuel is delivered to the combustion chamber when the throttle is released, and the engine doesn’t really slow.
Can you over tighten a chainsaw chain?
There is a tension screw located near the base of the bar on the chainsaw. To tighten the chain, turn it clockwise, and to loosen turn it counterclockwise. Don’t over-tighten the chain as this could cause it to break.
What is Swedish cope?
Using natural tree-shaped logs, Swedish Coped logs are hand-scribed together with saddle notched corners offering a tight fit between logs and protection against the elements.
Why do you debark logs?
Debarking helps speed the drying process. The bark can provide a hiding place for insects. After a log has been cut or a branch has been severed, insects have new openings that allow them to slip beneath the bark more easily. There, they can multiply and thrive, and they don’t need much space.
Can you drill holes in chainsaw bar?
Re: Drilling a Chainsaw Bar Drilling that bar may not be as difficult as you think. It will be best if you use a drill press, start with a pilot hole, and then drill to the size you need. Make sure you have a sharp bit, run at the lowest speed you can, and use cutting fluid.
Why is my chainsaw burning the wood?
Your chainsaw burns wood because of poor lubrication Lubrication allows the mechanical parts to coordinate much better by avoiding a phenomenon of friction which risks causing traces of burns. This is one of the main reasons that your appliance gives off too much heat and that the wood burns.
Can you run a chainsaw without the bar and chain?
You can run a chainsaw without a chain, but I wouldn’t recommend this for more than a few minutes. The engine will rev up higher, and these increases wear and tear. It can also run hot when the throttle is used. Ensure that you empty the bar oil tank, else oil can spray out of the chainsaw.
What is a chainsaw sprocket?
What is the drive sprocket? The drive sprocket and the clutch drum are connected to the saw motor. The sprocket is designed to drive the proper-pitched chain around the guide bar.
Why is my electric chainsaw smoking and not cutting?
This most commonly is a result of a dull chain and exerting to much pressure on the bar and chain trying to make the chain saw cut. This could also be either a lack of bar and chain oil ( tank empty, restricted oiler hole ) or an inferior type of oil that is being slung off the chain and not lubricating.
Do you start a chainsaw with the brake on?
When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
Why does my chainsaw bog down when I give it gas?
If your chainsaw is bogging down when you give it throttle, this is often a sign of improper gas-to-oil ratio. If there is too much gasoline in relation to the amount of oil used, this is known as a “rich mixture” and can cause the chainsaw to run poorly.
What does MS mean on Stihl chainsaws?
Every STIHL chainsaw model name starts with MS, MSA, or MSE. The common part, MS, stands for Motorsäge which is German for chainsaw. MSA indicates that it’s a battery chainsaw and MSE tells us that it’s an electric model.