Learning how to prevent your chainsaw from pinching when you’re cutting firewood is something everyone should understand. There are two easy techniques I like to use to prevent a chainsaw from pinching when the tree or tree top is already on the ground and you’re ready to cut it up into firewood sized pieces. Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Laziness has resulted in my chain and bar getting pinched in the compression side of a log on more occasions than I like to admit. More often than not, I get my blade and chain caught while trying to cut through a large log. I am down on one knee, the saw is cutting like through butter, and I just don’t want to stop and pound a wedge into the top of the cut to keep it from closing on my saw.
how to keep chainsaw from pinching Related Question:
How do I stop my chainsaw from pinching?
To stop your chainsaw from getting stuck, make a cut on top of the log or tree that’s preferably one-third of the log’s diameter. Use your chainsaw to cut from the underside until you meet the initial top cut. Always stand on the side when cross-cutting to prevent injury.
How do you cut down a tree without a pinching chainsaw?
Placing small pieces of firewood under the tree or using wedges are two easy ways to prevent your chainsaw from pinching when you’re cutting up a tree for firewood that’s already on the ground.
Can you fix a pinched chainsaw bar?
To open pinched rails, mount the bar in a vice and gently tap on the bent rail with a hammer and punch. A flat-blade screwdriver is another tool that can be useful for prying open bent bar rails. Once you’ve got the pinch worked out, test your repair by placing the chain back in the groove.
Why does my chainsaw always cut to the right?
One major reason a chainsaw curves to either the right or left during a cut is that it was unevenly sharpened. The unequal teeth of the chain cause it to take a different-sized bite into the wood. What is this? The uneven sharpness of the chain is mainly due to manual sharpening, especially with the use of a file.
How do you cut down a fallen tree under tension?
A felled tree will usually have saw-pinching areas where the top of the log is under compression and the bottom is under tension. If you have access to the top and bottom of the log, you can handle this one of two ways. Make a cut directly down from the top and then finish by cutting up from the bottom.
What is bucking a tree?
Bucking a tree The process of cutting a tree into usable lengths is called bucking. Bucking often occurs as a tree is being limbed, such as when the limbs of the crown are to be used as firewood. When cutting firewood, make sure you know the needed length of wood before you leave home.
Does a chainsaw bar wear out?
As a chainsaw bar wears out, you’ll lose cutting accuracy and efficiency. If the same type of cuts that your saw used to breeze through are now taking twice as long, and you’re sure that your chain is sharp enough, you might look at how worn your bar has become. Thankfully, there are a few simple ways to check this.
Why does my chainsaw cut curves?
Two main reasons will cause the chain to cut on a curve. The most common reason is from improper hand filing. If one side of the teeth is more heavily damaged, sharpening them down will make them smaller than the other side.
What causes a chainsaw to cut at a slant?
Check the size of the top plates, which sit on the longer sections of each tooth on the chain. These top plates should be the same size. If some are shorter than others, file the longer ones down to match. Keep the same angle on all the top plates as you file – angles that don’t match also can cause curved cutting.
Do I cut compression or tension first?
Always cut on the compression side first! The area on the outside of the bend will pull apart when cut. This is the tension side. If you decide to cut this side only, the tree will split apart before the cut can be completed.
What should you not do when a tree falls off?
When cutting up a felled tree, avoid touching the ground with the chain because even a brief encounter will severely dull the cutting teeth on your chain saw. If possible, cut partially through the tree and then rotate it to cut the rest of the way through.
Do you start a chainsaw with the brake on?
When using a chainsaw, you should always start it with the chain brake engaged so the chain does not move.
What is chainsaw kickback?
Kickback is the term to describe the unexpected upward motion of the guide bar. Kickback occurs when the end portion of the nose of the bar (the kickback zone) strikes an object and the chain momentarily snags, or is pinched.
Can you cut with the top of a chainsaw?
While it’s designed to cut with either the top or bottom of the blade, just about anything that comes in contact with the top half of the end tip of the blade (known as the kickback zone) can change the cutting momentum and cause the saw to slam back against you.
What does buck your hips mean?
be silent, stop talking etc.